J.M.Pearce (talk | contribs) m (→Source) |
J.M.Pearce (talk | contribs) m (→Source) |
||
Line 5: | Line 5: | ||
==Source== | ==Source== | ||
* Niklas Kretzschmar, Sami Lipponen, Ville Klar, Joshua M. Pearce, Tom L. Ranger, Jukka Seppälä, and Jouni Partanen. Mechanical Properties of Ultraviolet-Assisted Paste Extrusion and Postextrusion Ultraviolet-Curing of Three-Dimensional Printed Biocomposites. ''3D Printing and Additive Manufacturing''. 6(3) 127-137, 2019. https://doi.org/10.1089/3dp.2018.0148 [https://www.academia.edu/39160225/Mechanical_Properties_of_Ultraviolet-Assisted_Paste_Extrusion_and_Postextrusion_Ultraviolet-Curing_of_Three-Dimensional_Printed_Biocomposites open access] | * Niklas Kretzschmar, Sami Lipponen, Ville Klar, Joshua M. Pearce, Tom L. Ranger, Jukka Seppälä, and Jouni Partanen. Mechanical Properties of Ultraviolet-Assisted Paste Extrusion and Postextrusion Ultraviolet-Curing of Three-Dimensional Printed Biocomposites. ''3D Printing and Additive Manufacturing''. 6(3) 127-137, 2019. https://doi.org/10.1089/3dp.2018.0148 [https://www.academia.edu/39160225/Mechanical_Properties_of_Ultraviolet-Assisted_Paste_Extrusion_and_Postextrusion_Ultraviolet-Curing_of_Three-Dimensional_Printed_Biocomposites open access] | ||
[[image: | [[image:3dp.2019.6.issue-3.cover.jpg|right|500px]] | ||
==Abstract== | ==Abstract== |
Revision as of 02:43, 16 June 2019
Source
- Niklas Kretzschmar, Sami Lipponen, Ville Klar, Joshua M. Pearce, Tom L. Ranger, Jukka Seppälä, and Jouni Partanen. Mechanical Properties of Ultraviolet-Assisted Paste Extrusion and Postextrusion Ultraviolet-Curing of Three-Dimensional Printed Biocomposites. 3D Printing and Additive Manufacturing. 6(3) 127-137, 2019. https://doi.org/10.1089/3dp.2018.0148 open access
Abstract
Three-dimensional (3D) printing of biomaterials has the potential to become an ecologically advantageous alternative compared with conventional manufacturing based on oil-derived polymer materials. In this study, a novel 3D printing technology is applied that combines ultraviolet (UV) curing with paste extrusion. This hybrid manufacturing technique enables the fabrication of complex geometries from high filler-ratio pastes. The developed biocomposite aims for suitable mechanical properties in terms of tensile and compressive strength. It is composed of acrylic acid, cellulose acetate, α-cellulose, and fumed silica with a cellulose ratio of more than 25 vol-%. The material is extruded with an in-house-developed 3D printer equipped with a 12 W UV light curing source, which enables concurrent curing and extrusion. Two different UV-curing strategies were tested: postcuring without concurrent curing and postcuring with concurrent curing. The total UV-curing duration was kept constant with all samples. Tensile testing in accordance with ASTM standard D638-14 Type 4, compression testing according to ASTM D695-15, and overhang tests were conducted. As a result, samples without notable shrinkage, suitable tensile strength (up to 17.72 MPa), competitive compression testing parameters (up to 19.73 MPa), and an enhanced overhang angle (increase of more than 25°) were produced, leading to new applications and more freedom in design due to higher possible unsupported overhangs when using UV-curing during the print. Overall, constant UV light radiation during the print leads to improved mechanical properties due to the possibility of bypassing the UV-penetration depth constraint. It should be considered when extruding photopolymer-based composites, especially for large and complex components with a low degree of translucency.
Keywords
3D printing; Mechanical testing; Natural fibre ; Natural fibre composites; Biopolymers; UV-assisted paste extrusion; biocomposite; 3D printing; mechanical properties; overhang testing; open-source platform
See Also
- Mechanical Properties of Components Fabricated with Open-Source 3-D Printers Under Realistic Environmental Conditions
- Tensile Strength of Commercial Polymer Materials for Fused Filament Fabrication 3-D Printing
- Anisotropic mechanical property variance between ASTM D638-14 type I and type IV fused filament fabricated specimens
- The Effects of PLA Color on Material Properties of 3-D Printed Components
- Mechanical properties of 3-D printed truss-like lattice biopolymer non-stochastic structures for sandwich panels with natural fibre composite skins
- Wood Furniture Waste-Based Recycled 3-D Printing Filament