Search results

Create the page "Screws" on this wiki! See also the search results found.

• Surgical Education Learners Forum
  powered drill to insert self-drilling Schanz screws through the near cortex and then manually advance Schanz screws into the far cortex to avoid plunging. Uniplanar
  3 KB (1,647 words) - 14:27, 3 June 2024
• MOST RepRap build
  4 M4X50mm screws 1 Budaschnozzle 1.2 0.5 mm(LulzBot) 4 springs 6 m4 nuts 10 m4 washers 2 m4 x 20 mm screws 1 stepper motor 4 m3x10mm screws 4 m3 washers
  26 KB (4,116 words) - 14:03, 6 June 2022
• Global Surgical Training Challenge
  powered and manual drilling, positioning and correctly inserting Schanz screws, and constructing the rod-to-rod modular frame as part of external fixation
  14 KB (1,521 words) - 13:43, 27 September 2023
• MOST RepRap Primer (section Lead Screw and Captive Nut)
  The RepRap is built with metric screws, which aren't as common in the US as in other parts of the world. Metric screws have a pretty simple naming convention
  21 KB (3,442 words) - 10:52, 6 December 2023
• Open-source metal 3-D printer
  with M3 X 10mm screws with washers. Insert two M3 nuts into the set screw nut traps in the pulley, loosely insert two M3 X 8mm set screws into the pulley
  30 KB (2,601 words) - 14:43, 28 February 2024
• Open-Source Grinding Machine for Compression Screw Manufacturing
  capable of replicating commercial screws as well as providing makers with much greater flexibility to make custom screws. This invention enables the DRAM
  5 KB (990 words) - 18:36, 19 September 2024
• Tibial Fracture Fixation
  alignment, the Schanz screws did not perforate the far cortex of the Tibial Shaft Transverse Fracture Simulator, and the Schanz screws are properly positioned
  32 KB (4,196 words) - 11:52, 28 February 2024
• Humeral Fracture Fixation
  powered drill to insert self-drilling Schanz screws through the near cortex and then manually advance Schanz screws into the far cortex to avoid plunging. A
  34 KB (4,211 words) - 18:23, 29 January 2024
• Athena Wiring
  the wider part of the printed mount with two M3 x 6mm screws(see photo). Do not tighten the screws yet - leave the board loose on the mount. Mount the small
  10 KB (1,463 words) - 11:57, 16 September 2024
• Uniplanar External Fixation
  powered drill to insert self-drilling Schanz screws through the near cortex and then manually advance Schanz screws into the far cortex to avoid plunging. A
  39 KB (4,816 words) - 17:08, 28 February 2024
• Athena Motor End Assembly
  both of them! Motor end with screws. Prepare twelve M3×12mm socket head cap screws each with an M3 washer. Stand the motor end assembly up on one linking board
  5 KB (837 words) - 10:03, 16 September 2024
• RepRapable Recyclebot: Open source 3-D printable extruder for converting plastic to 3-D printing filament
  compliments of Marcin at Open Source Ecology - removed all the nuts and bolts and screws Please note that all the instructions are in the HardwareX article above
  7 KB (1,342 words) - 21:43, 16 April 2024
• Athena Idler End Assembly
  linking boards. Secure the two together with six #6 x 3/4" screws. Prepare six M2 x 12mm screws with washers on them for securing the limit switches. Apply
  8 KB (1,249 words) - 10:00, 16 September 2024
• Delta Vertical Boards:MOST
  flush with the end of the screw. Mounting controller to vertical board. Prepare 4 M3 x 25mm screws with washers. Pass the screws through the controller mounting
  8 KB (990 words) - 23:18, 7 July 2022
• Athena Extruder Drive and Spool Holder Assembly
  Place washers on the two M3 x 45mm screws. Push one of the screws through the hole in the fuel line. Using one screw to align idler housing. Place the idler
  7 KB (1,004 words) - 09:47, 16 September 2024
• Athena Frame Assembly
  engagement screws in the carriages with the tip of the precision knife. Plastiform M3 x 12mm screws into the holes leaving the heads of the screws sitting
  17 KB (2,693 words) - 09:48, 16 September 2024
• Multi-material additive and subtractive prosumer digital fabrication with a free and open-source convertible delta RepRap 3-D printer
  the set screws facing the flat on the shaft. Do not tighten the set screws. Start a nut on the lead screw. Start an M5 nut on the M5 lead screw and thread
  24 KB (3,220 words) - 19:07, 16 April 2024
• Delta Idler End:MOST
  end. Start four #6 x 3/4" sheet metal screws into the tab and linking board but do not tighten until all of the screws are started and the position of the
  5 KB (638 words) - 23:39, 7 July 2022
• Open-source syringe pump
  motor into the motor end using 4 M3 washers and 4 M3 x 20mm socket head cap screws. 2 Metal rods inserted in motor end Insert the 2 metal rods into motor end
  22 KB (2,305 words) - 11:22, 9 August 2024
• Delta Motor End Assembly:MOST
  against the stop on the motor mount. Once in position, tighten the screws. (Two screws per tab are probably sufficient, but maximum rigidity and longer maintenance
  4 KB (403 words) - 23:42, 7 July 2022