Create the page "Piem" on this wiki! See also the search results found.
- cylindrical funnel through which water enters a vertical pipe (2). At the bottom of this pipe, two (or more) radial pipes (3) are provided with bends to21 KB (3,561 words) - 14:13, 10 December 2023
- - Black Steel Plate 4mm 16 - Coupling 90mm/100mm 14 - Galv. Pipe 33mm/42mm 12 - Galv. Pipe 80mm/90mm2 KB (180 words) - 14:05, 10 December 2023
- Distance from source to pump (drive pipe length) Distance from pump to delivery site (delivery pipe length) 1. Drive Pipe - Heavy gauge galvanised steel or30 KB (4,644 words) - 14:45, 29 January 2024
- over the top of 1 ½ inch vertical pipe. The vertical pipe in the initial settling tank determines the water line. This pipe runs through a hole (sealed) in13 KB (2,300 words) - 16:39, 29 January 2024
- Determine equivalent length of pipe by adding actual length of pipe and equivalent lengths of fittings based on tables using pipe size. Find Frictional Pressure9 KB (1,258 words) - 08:15, 29 March 2024
- adjustable pipe system to solve these problems. Using only one PVC pipe size to draw up water at any depth up to 60 meters, this length of pipe may be lowered32 KB (4,120 words) - 16:17, 29 January 2024
- deep A 1mx1m culvert pipe made from concrete was lowered into the hole A cement floor was added to the bottom of the culvert pipe to prevent fecal matter4 KB (508 words) - 13:19, 23 October 2023
- elbow on the EXIT PIPE. This elbow must be able to rotate on the pipe from the outlet compartment. After biogas is produced, the EXIT PIPE must be set at10 KB (1,281 words) - 14:26, 23 October 2023
- first tank closer to the marsh and connecting the inlet pipe to the pipe-to-marsh pipe. Because the top of the surge tank and the inlet and outlet pipes were35 KB (4,893 words) - 19:32, 29 January 2024
- descending water pipe. If the collector heats up the water, the water rises again and reaches the tank through an ascending water pipe at the upper end14 KB (2,094 words) - 14:01, 25 May 2023
- contaminated water in a length of pipe that is capped at the end. When the pipe is filled with water, a ball shuts off the top of the pipe so additional rainfall23 KB (2,313 words) - 12:26, 28 February 2024
- create enough depth to allow for screened pipe diversion. These "screened vault intakes" consist of a screened pipe placed in a pre-cast concrete vault set23 KB (3,393 words) - 16:33, 28 February 2024
- roof area. Another method would be to use pipe sizing/friction tables to find an acceptable amount of friction. Pipe size to roof area table. Using rule of7 KB (1,080 words) - 21:55, 15 January 2024
- sink again and b) we could run a PVC pipe to the heater for cold water intake. We started by cutting off the pipe as far back as it was cracked. Upon further23 KB (3,370 words) - 12:29, 6 March 2024
- the pipe is blocked and the other is tilted out of the soil to allow filling. The pipes were laid end to end below the soil surface. When the pipe is filled11 KB (1,675 words) - 12:01, 28 February 2024
- descending water pipe. If the collector heats up the water, the water rises again and reaches the tank through an ascending water pipe at the upper end9 KB (1,900 words) - 12:42, 9 August 2023
- constructed wetland tank through a one and a half inch diameter PVC pipe. The pipe enters the tank at the bottom of the side through a water tight bulkhead16 KB (2,377 words) - 20:46, 22 August 2023
- reasons. This retrofit maintains all the required pipe ventilation and meets or exceeds the minimum pipe slope requirements. Somewhere online I researched19 KB (3,111 words) - 14:57, 23 October 2023
- in Adobe wall to run PVC pipe to rooftop collector. Threaded ends slide on copper pipe. Close-up: threaded end on copper pipe.. Soldering copper threaded22 KB (3,012 words) - 19:08, 29 January 2024
- galvanized pipe using the appropriate tools. Step 4. (10 minutes) Demonstrate and describe the joining of galvanized pipe using pipe wrenches and pipe joint35 KB (2,816 words) - 09:30, 28 August 2023
