(Created page with "==MY4777 Open Source 3D Printing Class Student Profile== {{userboxtop}} {{User OSH}} category:MY4777 {{User 3D printing}} {{userboxbottom}} ==Delta Prints== {{Gallery |w...") |
No edit summary |
||
Line 1: | Line 1: | ||
==MY4777 Open Source 3D Printing Class Student Profile== | ==MY4777 Open Source 3D Printing Class Student Profile== | ||
4th year Electrical Engineering student at Michigan Tech. This class is my first experience with 3D printing hardware and software. | |||
{{userboxtop}} | {{userboxtop}} | ||
{{User OSH}} | {{User OSH}} | ||
Line 9: | Line 9: | ||
==Delta Prints== | ==Delta Prints== | ||
{{Gallery | {{Gallery | ||
| | |title=1.75mm Black PLA Zentoolworks | ||
| | |Image:Dogtoy shadowView.jpg|Dogtoy XY Calibration Print | ||
| | |Image:GreatRhombi.jpg|Great Rhombi test print | ||
|Image: | |||
}} | }} | ||
Line 19: | Line 17: | ||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
! | ! Date | ||
! | ! Issue | ||
! | ! Status | ||
! Solution | |||
|- | |- | ||
| | | 09/20/2014 | ||
| | | Filament won't enter hot end. Gets stuck in the 1/4" wider gap between PFT tube and hot end internal PFT. | ||
| | | Rough Fix | ||
| | | Inserted 1/4" piece of PFT tube into the gap. Flared opening. | ||
|- | |||
| 09/20/2014 | |||
| Filament won't extrude out of hot end | |||
| Fixed | |||
| "Heat-to-cool" declogging approach did not work multiple times. Required to heat hot end, push pin into nozzle to push up obstruction, and then cool and extract. This way filament could "grab" obstruction before cooling. | |||
|- | |- | ||
| | |09/25/2014 | ||
| Repetier Host won't begin print sequence but other controls work fine. Temp feedback freezes. | |||
| Temporary Work Around | |||
| Using Pronterface, can consistently read temp and initiate print sequence. | |||
|- | |- | ||
|09/25/2014 | |||
| Filament doesn't extrude during print. Oozes fine when not printing. | |||
| In progress | |||
| Most likely another clog | |||
|} | |} | ||
[[category:3D printing]] | [[category:3D printing]] |
Revision as of 02:04, 1 October 2014
MY4777 Open Source 3D Printing Class Student Profile
4th year Electrical Engineering student at Michigan Tech. This class is my first experience with 3D printing hardware and software. Template:Userboxtop Template:User OSH Template:User 3D printing Template:Userboxbottom
Delta Prints
Print Issues & Modifications Log
Date | Issue | Status | Solution |
---|---|---|---|
09/20/2014 | Filament won't enter hot end. Gets stuck in the 1/4" wider gap between PFT tube and hot end internal PFT. | Rough Fix | Inserted 1/4" piece of PFT tube into the gap. Flared opening. |
09/20/2014 | Filament won't extrude out of hot end | Fixed | "Heat-to-cool" declogging approach did not work multiple times. Required to heat hot end, push pin into nozzle to push up obstruction, and then cool and extract. This way filament could "grab" obstruction before cooling. |
09/25/2014 | Repetier Host won't begin print sequence but other controls work fine. Temp feedback freezes. | Temporary Work Around | Using Pronterface, can consistently read temp and initiate print sequence. |
09/25/2014 | Filament doesn't extrude during print. Oozes fine when not printing. | In progress | Most likely another clog |