|
|
| Line 15: |
Line 15: |
| ==Equipment or Bill of Materials== | | ==Equipment or Bill of Materials== |
|
| |
|
| | Information about how to construct a delta-based metal printer for under $1500 can be found [[Open-source_metal_3-D_printer|here]]. |
|
| |
|
| {| class="wikitable"
| | # [[Open-source_metal_3-D_printer|Delta-based metal printer]] |
| |-
| | # Clean substrate ([[Aluminum_substrate_cleaning_for_3-D_printing:MOST|aluminum]] or [[Steel_substrate_cleaning_for_3-D_printing:MOST|steel]]) |
| | '''Item'''
| | # Bucket of water for quench |
| | '''Number'''
| | # Tongs |
| | '''Cost(USD)'''
| | # Appropriate heat resistive gloves |
| | '''Source'''
| | # Appropriate eye protection |
| |-
| |
| | All 12 Printed Parts @ $40/kg
| |
| |
| |
| | $12.00
| |
| | Local [[RepRap]]
| |
| |-
| |
| | valign="BOTTOM" | '''All Fasteners'''
| |
| | valign="BOTTOM" |
| |
| | valign="BOTTOM" | $2.00
| |
| | http://www.mcmaster.com/
| |
| |-
| |
| | M3 nut
| |
| | 90
| |
| |
| |
| | valign="BOTTOM" |
| |
| |- | |
| | M3x10 mm screw
| |
| | 12
| |
| |
| |
| |
| |
| |-
| |
| | M3x12mm screw
| |
| | 48
| |
| |
| |
| |
| |
| |-
| |
| | M3x20mm screw
| |
| | 12
| |
| |
| |
| |
| |
| |-
| |
| | M3x8mm set screw
| |
| | 6
| |
| |
| |
| |
| |
| |-
| |
| | M3washer
| |
| | 102
| |
| |
| |
| |
| |
| |-
| |
| | M8nut
| |
| | 6
| |
| |
| |
| |
| |
| |-
| |
| | M8set screw
| |
| | 3
| |
| |
| |
| |
| |
| |-
| |
| | 152mm x 152mm ceramic insulation
| |
| | 1
| |
| | $ 4.00
| |
| |
| |
| |-
| |
| | '''Rods,bearings and ties'''
| |
| |
| |
| |
| |
| | http://www.amazon.com/
| |
| |-
| |
| | 300mm x 8mm smooth rod
| |
| | 6
| |
| | $25.00
| |
| | valign="BOTTOM" |
| |
| |-
| |
| | 304.8mm carbon fiber rod
| |
| | 6
| |
| | $6.00
| |
| |
| |
| |-
| |
| | 608zz bearings
| |
| | 6
| |
| | $2.40
| |
| |
| |
| |-
| |
| | LM8UUbearings
| |
| | 6
| |
| | $6.00
| |
| |
| |
| |-
| |
| | Small wire ties
| |
| | 3
| |
| | $0.50
| |
| |
| |
| |-
| |
| | Tie rod end
| |
| | 24
| |
| | $ 8.00
| |
| |
| |
| |-
| |
| | 600mm T5 belt
| |
| | 3
| |
| | $ 5.90
| |
| | http://www.polytechdesign.com/
| |
| |-
| |
| | 241mm x 51mm x 4mm Aluminum plate
| |
| | 3
| |
| | $114.00
| |
| | Local machine shop
| |
| |-
| |
| | NEMA17 Stepper motor (1.8 deg.,5.5kg-cm holding torque, 750mm wire)
| |
| | 3
| |
| | $39.00
| |
| | http://www.kysanelectronics.com/
| |
| |- | |
| | Mechanical limit switch
| |
| | 3
| |
| | $3.33
| |
| | http://www.digikey.com/
| |
| |- | |
| | Melzi Microcontroller board
| |
| | 1
| |
| | $120.00
| |
| | http://matterfy.com/
| |
| |-
| |
| | Millermatic 140 Auto-set MIG Welder with Cart
| |
| | 1
| |
| | $836.00
| |
| | http://www.millerwelds.com/
| |
| |-
| |
| | Power supply
| |
| | 1
| |
| | $8.00
| |
| | (Recycled)/Internet
| |
| |-
| |
| | Wires
| |
| | 1
| |
| | $ 2.00
| |
| | (Recycled)/Internet
| |
| |-
| |
| | valign="BOTTOM" | <br />
| |
| | '''Total'''
| |
| | '''$1,194.13 '''
| |
| | <br />
| |
| |}
| |
|
| |
|
| | | Appropriate level of PPE depends on your equipment set up, detailed further in the Safety section. |
| ===Printed Parts===
| |
| [[image:Metalp.png|right]]
| |
| Print these STL files on any flavor of [[RepRap]]. The red parts in the image on the right are the printed parts. The [https://github.com/mtu-most/MOST-delta-stage/blob/master/scad SCAD] if you need it.
| |
| | |
| * 3X [[File:End motor.stl]]
| |
| * 3X [[File:End idler.stl]]
| |
| * 3X [[File:Belt terminators.stl]]
| |
| * 3X [[File:MOST_12_tooth_pulley.stl]]
| |
| *[[File:Effector.stl]]
| |
| *[[File:Carriage.stl]]
| |
| *[[File:Bed adapter.stl]]
| |
|
| |
|
| ==Calibration & Tolerances== | | ==Calibration & Tolerances== |
