We continue to develop resources related to the COVID-19 pandemic. See COVID-19 initiatives on Appropedia for more information.

Difference between revisions of "Seed Spreader / Salt Shaker"

From Appropedia
Jump to navigation Jump to search
 
(5 intermediate revisions by the same user not shown)
Line 11: Line 11:
 
==Abstract==
 
==Abstract==
 
# With an over abundance of plastic bottles, there should be some attachments that can be made to make tools out of them! This design can fit any 2L bottle and can be scales down to fit other size bottles. This takes an old 2L pop bottle and turns it into a seed spreader/shaker. With the handle and easy to use adjuster, it is easy to control the flow of whatever you are spreading. Here in the North, this could also be used as a salt spreader for the winter months.
 
# With an over abundance of plastic bottles, there should be some attachments that can be made to make tools out of them! This design can fit any 2L bottle and can be scales down to fit other size bottles. This takes an old 2L pop bottle and turns it into a seed spreader/shaker. With the handle and easy to use adjuster, it is easy to control the flow of whatever you are spreading. Here in the North, this could also be used as a salt spreader for the winter months.
# Picture of completed print using your printer [[Image:Wood_WorkingClamp_Parts.png|200px|right]]
+
[[Image:Kjkurtz spreaderassemb2.png|200px|right]]
  
 
== Bill of Materials==
 
== Bill of Materials==
Line 35: Line 35:
 
# Add the screws and the handle to the bottle
 
# Add the screws and the handle to the bottle
  
# print time estimate - 6.5 hours
+
Print time estimate - 6.5 hours , Assembly time estimate - 10 minutes
# assembly time estimate - 10 minutes
 
  
# Including drawings or pictures of the device at stage of assembly at minimum. (http://www.appropedia.org/Special:Upload)
+
 
 +
 
 +
<gallery caption="Seeder Assembly">
 +
Image:Kjkurtz spreaderassemb.png| All Materials
 +
Image:Kjkurtz spreaderassemb1.png| Press Fit Caps and Handle Ring
 +
Image:Kjkurtz spreaderassemb2.png| Fully Assembled with Handle
 +
</gallery>
  
 
=== Common Problems and Solutions===
 
=== Common Problems and Solutions===
Line 61: Line 66:
 
<references/>  
 
<references/>  
 
<nowiki>
 
<nowiki>
Based on the developmental needs addressed (e.g. food, heat, electricity, clean water, health  care, etc.) be sure to label your device in the proper categories e.g. use [[Category:Water]]. Be sure to categorize your device so that it will be easy to find – for example “Low voltage connection basics” is categorized in
+
 
  
 
[[Category:How tos]]
 
[[Category:How tos]]

Latest revision as of 20:39, 5 December 2019

MOST Delta filament as guide.JPG This page was part of an MTU course MSE4777 OA and MSE4777 OB/MSE5777/EE4777/EE5777: Open-source 3-D printing

Please leave comments using the discussion tab. The course runs in the Fall semester. It is not open edit.


2L Seeder / Salt Shaker[edit]

Project developed by [[[User:Kjkurtz|Kjkurtz]] (talk)]
Status
This OSAT has been designed but not yet tested - use at own risk.
This OSAT has been prototyped.

You can help Appropedia by contributing to the next step in this OSAT's status.

Abstract[edit]

  1. With an over abundance of plastic bottles, there should be some attachments that can be made to make tools out of them! This design can fit any 2L bottle and can be scales down to fit other size bottles. This takes an old 2L pop bottle and turns it into a seed spreader/shaker. With the handle and easy to use adjuster, it is easy to control the flow of whatever you are spreading. Here in the North, this could also be used as a salt spreader for the winter months.
Kjkurtz spreaderassemb2.png

Bill of Materials[edit]

  1. 4 6/32 Hex Nuts
  2. 4 6/32 0.5in Bolts
  3. 100g of PLA Filament
  1. Link to all Source CAD and STL's [1]

Tools needed for fabrication of the OSAT[edit]

  1. MOST Delta RepRap or similar RepRap 3-D printer
  2. Screwdriver and Pliers needed for Final Assembly

Skills and Knowledge Necessary to Make the OSAT[edit]

  • If you used special skill – link to relevant Wikipedia or Wikiversity articles/courses

Technical Specifications and Assembly Instructions[edit]

  1. Lay out all printed parts and hardware.
  2. Cut off Bottom of 2L Bottle
  3. Slip Handle top over the top of bottle
  4. Slip the end cap over the connecting cap as shown in the image
  5. Cut a small hole in the bottle for the securement screws
  6. Add the screws and the handle to the bottle

Print time estimate - 6.5 hours , Assembly time estimate - 10 minutes


Common Problems and Solutions[edit]

  • Do not cut the hole too large for the connecting hardware, use a knife to cut a small slot or use a drill to avoid frustration

Cost savings[edit]

  • If your solution is not a low cost one then it is not really appropriate.
  1. Hardware Costs for Nuts and Bolts $1
  2. Filament Costs @100g is approximately $2
  3. Total Cost is $3
  4. Commercial equivalent for a salt shaker [2]
  5. For the salt shaker savings of $5 or 62.5%, however it can be used to spread multiple sizes where the example has a maximum diameter is can spread.

Benefited Internet Communities[edit]

  • Michigan Sportsman - Deer Management [3]
  • Michigan Tech Reddit [4]

References[edit]

  • Initial idea for the design [5]


[[Category:How tos]] [[Category:Deer Management]] [[Category:Salt Shaker]] [[Category:Winter]]. [[Category:House Hold Items]]