J.M.Pearce (talk | contribs) mNo edit summary |
J.M.Pearce (talk | contribs) mNo edit summary |
||
Line 37: | Line 37: | ||
# '''Could have 2 print heads - one FFF and one dump powder for save reasons as above''' [[User:J.M.Pearce|Joshua]] ([[User talk:J.M.Pearce|talk]]) 07:39, 1 December 2015 (PST) | # '''Could have 2 print heads - one FFF and one dump powder for save reasons as above''' [[User:J.M.Pearce|Joshua]] ([[User talk:J.M.Pearce|talk]]) 07:39, 1 December 2015 (PST) | ||
# '''Use inert pellets as fill in large 3DP - as in concrete aggregate 3DP'''[[User:J.M.Pearce|Joshua]] ([[User talk:J.M.Pearce|talk]]) 07:43, 1 December 2015 (PST) | # '''Use inert pellets as fill in large 3DP - as in concrete aggregate 3DP'''[[User:J.M.Pearce|Joshua]] ([[User talk:J.M.Pearce|talk]]) 07:43, 1 December 2015 (PST) | ||
# Cool 3DP with inert liquid during print [[User:J.M.Pearce|Joshua]] ([[User talk:J.M.Pearce|talk]]) 07:48, 1 December 2015 (PST) | |||
# Maintain temperature of 3DP to avoid crystalization by immersing in inert liquid during printing [[User:J.M.Pearce|Joshua]] ([[User talk:J.M.Pearce|talk]]) 07:48, 1 December 2015 (PST) | |||
# 3DP with inert fluid - and freeze in location - print ice, print coolants at lower T -- [[User:J.M.Pearce|Joshua]] ([[User talk:J.M.Pearce|talk]]) 07:48, 1 December 2015 (PST) | |||
# 3DP with fluid to allow for overhangs, bridges, and drain when complete --[[User:J.M.Pearce|Joshua]] ([[User talk:J.M.Pearce|talk]]) 07:48, 1 December 2015 (PST) | |||
# Float 3DP components into place on inert fluid [[User:J.M.Pearce|Joshua]] ([[User talk:J.M.Pearce|talk]]) 07:48, 1 December 2015 (PST) |
Revision as of 15:48, 1 December 2015
- Print in vacuum to avoid contamination Joshua (talk) 07:30, 1 December 2015 (PST)
- Print with inert gas for GMAW 3DP Joshua (talk) 07:30, 1 December 2015 (PST)
- Print with inert gas injected into plastic to reduce weight Joshua (talk) 07:30, 1 December 2015 (PST)
- Print with inert gas injected into metal to reduce weight Joshua (talk) 07:30, 1 December 2015 (PST)
- Print with inert gas injected into ceramic to reduce weight Joshua (talk) 07:30, 1 December 2015 (PST)
- Print with inert gas around object to avoid ionizing radiation from ruining resolution in SLA Joshua (talk) 07:30, 1 December 2015 (PST)
- Print with inert gas atmosphere while exposing to ionizing radiation to set up location of voxel Joshua (talk) 07:30, 1 December 2015 (PST)
- Print with inert gas inside a sol for insulation Joshua (talk) 07:32, 1 December 2015 (PST)
- Print with inert gas to create foam to 3DP isolation Joshua (talk) 07:32, 1 December 2015 (PST)
- Print with inert gas in hyper cold environment to have inert gas solid Joshua (talk) 07:32, 1 December 2015 (PST)
- Print with inert gas in vacuum to have 3D printed gas in space Joshua (talk) 07:32, 1 December 2015 (PST)
- Print with inert gas injected into window in final step for low 3 glass multipane windows in 3DP home Joshua (talk) 07:35, 1 December 2015 (PST)
- Print with inert gas injected into walls in final step for energy efficient 3DP home Joshua (talk) 07:35, 1 December 2015 (PST)
- Print with inert gas injected into ceiling/floor in final step for energy efficient 3DP home Joshua (talk) 07:35, 1 December 2015 (PST)
- Blow inert gas with pressure during FFF to improve resolution of fine prints Joshua (talk) 07:35, 1 December 2015 (PST)
- Blow inert gas at 3D print at end of print to remove from print bedJoshua (talk) 07:35, 1 December 2015 (PST)
- Cool motors of 3DP to drive higher speeds with inert gasJoshua (talk) 07:35, 1 December 2015 (PST)
- Print head as spaceship - use inert gas jets to move head into position for 3DP --Joshua (talk) 07:37, 1 December 2015 (PST)
- Print head as sail boat - use inert gas jets to move head into position for 3DP --Joshua (talk) 07:37, 1 December 2015 (PST)
- Surface for printing is "bed" of moving inert gas - shifts to position under printhead Joshua (talk) 07:37, 1 December 2015 (PST)
- For SLA printing deposit inert powder as filler to allow for overhangs Joshua (talk) 07:39, 1 December 2015 (PST)
- For SLA printing deposit inert active material to add functionality while being caged inside print Joshua (talk) 07:39, 1 December 2015 (PST)
- e.g. electronics
- e.g. LED
- e.g. gas sensor
- Print with inert powder as filler in FFF to allow for lower costs Joshua (talk) 07:39, 1 December 2015 (PST)
- e.g. for dumping waste to add weight
- e.g. to avoid overhangs as internal fill
- Could have 2 print heads - one FFF and one dump powder for save reasons as above Joshua (talk) 07:39, 1 December 2015 (PST)
- Use inert pellets as fill in large 3DP - as in concrete aggregate 3DPJoshua (talk) 07:43, 1 December 2015 (PST)
- Cool 3DP with inert liquid during print Joshua (talk) 07:48, 1 December 2015 (PST)
- Maintain temperature of 3DP to avoid crystalization by immersing in inert liquid during printing Joshua (talk) 07:48, 1 December 2015 (PST)
- 3DP with inert fluid - and freeze in location - print ice, print coolants at lower T -- Joshua (talk) 07:48, 1 December 2015 (PST)
- 3DP with fluid to allow for overhangs, bridges, and drain when complete --Joshua (talk) 07:48, 1 December 2015 (PST)
- Float 3DP components into place on inert fluid Joshua (talk) 07:48, 1 December 2015 (PST)