(→Files) |
Page script (talk | contribs) (Normalize galleries) |
||
(19 intermediate revisions by 5 users not shown) | |||
Line 1: | Line 1: | ||
[[File:Wire_holder_finalrev.jpg|thumb|right|Printed Wire Holder]] | [[File:Wire_holder_finalrev.jpg|thumb|right|Printed Wire Holder]] | ||
[[File:Wire_holder_in_lab.jpg|thumb|right|Wire holder being used in an MTU undergrad electronic lab]] | [[File:Wire_holder_in_lab.jpg|thumb|right|Wire holder being used in an MTU undergrad electronic lab]] | ||
==Team== | ==Team== | ||
Line 19: | Line 20: | ||
An open source wire lead holder that can be easily printed for any lab. Saving both time and money. | An open source wire lead holder that can be easily printed for any lab. Saving both time and money. | ||
A commercial off the shelf wire holder would cost about $15, this holder will cost $2. | A commercial off the shelf wire holder would cost about $15, this holder will cost $2.03 to print and mount. | ||
It can be printed in just a few hours which would be much faster than if you had to order and ship one. | It can be printed in just a few hours which would be much faster than if you had to order and ship one. | ||
Line 25: | Line 26: | ||
'''Bill Of Materials''' | '''Bill Of Materials''' | ||
*3x #6 sheet metal screws @ $0. | *3x #6 sheet metal screws @ $0.11 per screw | ||
*Approximately 70 grams of PLA or equivalent filament @$0.24 per gram. $1.70 | *Approximately 70 grams of PLA or equivalent filament @$0.24 per gram. $1.70 | ||
Total Cost ~$2. | Total Cost ~$2.03 | ||
[https://www.adafruit.com/product/2624 Versus $15 Pomona Holder] | |||
'''Print Settings and Instructions''' | |||
* 0.2 mm layer height | |||
* 2 perimeters | |||
* 3 top and bottom layers | |||
* 20% infill | |||
These settings will deliver good quality and strong results. | |||
'''Installation and Use''' | '''Installation and Use''' | ||
Line 35: | Line 44: | ||
==Files== | ==Files== | ||
<gallery> | |||
Image:printable_wire_holder.JPG|Wire Holder Model | |||
[http://3dprint.nih.gov/discover/3DPX-004032 Model Files] | |||
</gallery> | |||
{{Page data}} | |||
[[Category:Devices]] |
Latest revision as of 23:34, 2 May 2022
Team[edit | edit source]
Nicholas Lanter Undergrad student, Computer Engineering
Logan Brueck Undergrad student, Mechanical Engineering
Project[edit | edit source]
Test Lead Holder
An open source wire lead holder that can be easily printed for any lab. Saving both time and money.
A commercial off the shelf wire holder would cost about $15, this holder will cost $2.03 to print and mount. It can be printed in just a few hours which would be much faster than if you had to order and ship one.
Prototype[edit | edit source]
Bill Of Materials
- 3x #6 sheet metal screws @ $0.11 per screw
- Approximately 70 grams of PLA or equivalent filament @$0.24 per gram. $1.70
Total Cost ~$2.03 Versus $15 Pomona Holder
Print Settings and Instructions
- 0.2 mm layer height
- 2 perimeters
- 3 top and bottom layers
- 20% infill
These settings will deliver good quality and strong results.
Installation and Use
- Install using 3x #6 sheet metal screws and slide wire holder over screws, then tighten.
Files[edit | edit source]
-
Wire Holder Model