(24 intermediate revisions by 6 users not shown) | |||
Line 1: | Line 1: | ||
Publication Number T-114 | Publication Number T-114 | ||
Go back to [[AT_Sourcebook]] | |||
[[Category:Appropriate_technology]] | |||
[[Category:Energy]] | |||
[[Category:Renewable energy]] | |||
=== | === Abstract === | ||
This document gives schematic drawings of the assembly and operation of a wind powered water pump. The drawings are accompanied by a list of parts and materials used in the pumps manufacturing. | |||
[ | === Publisher === | ||
[http://www.mcgill.ca/brace/ Brace Research Institute]<br /> | |||
MacDonald College<br /> | |||
[ | [http://www.mcgill.ca/ McGill University]<br /> | ||
Ste. Anne de Bellevue 800<br /> | |||
Quebec, Canada<br /> | |||
H9X 1CO<br /> | |||
1977 | |||
===List of Parts and Materials=== | = Installation = | ||
[[Image:Pg1.jpg|thumb|Page 1 - Installation (not to scale)|center]] | |||
= Assembly = | |||
[[Image:Pg2.jpg|thumb|Page 2 - Assembly (not to scale)|center]] | |||
[[Image:Pg3.jpg|thumb|Page 3 - Assembly |center]] | |||
= Piston and Piston Rod = | |||
[[Image:Pg4.jpg|thumb|Page 4 - Piston Rod (not to scale) |center]] | |||
[[Image:Pg5.jpg|thumb|Page 5 - Piston (not to scale)|center]] | |||
= Washers and Piston Head = | |||
[[Image:Pg6.jpg|thumb|Page 6 - Schematic of Rubber Washer and Steel plate (not to scale)|center]] | |||
[[Image:Pg7.jpg|thumb|Page 7 - Schematic of Black Steel Plates|center]] | |||
= Operation = | |||
[[Image:Pg8.jpg|thumb|Page 8 - Pump Operational Steps|center]] | |||
= Parts and Materials = | |||
[[Image:Pg9.jpg|thumb|Page 9 - List of Parts and Materials|center]] | |||
==List of Parts and Materials== | |||
* 36 - Nut Bored at 8mm | * 36 - Nut Bored at 8mm | ||
* 34 - Round HD-Screw 4mm | * 34 - Round HD-Screw 4mm | ||
Line 32: | Line 51: | ||
* 14 - Galv. Pipe 33mm/42mm | * 14 - Galv. Pipe 33mm/42mm | ||
* 12 - Galv. Pipe 80mm/90mm | * 12 - Galv. Pipe 80mm/90mm | ||
[[Category: Wind power]] | |||
[[Category: Water supply]] | |||
[[Category: Pumping]] | |||
Revision as of 02:20, 7 October 2010
Publication Number T-114 Go back to AT_Sourcebook
Abstract
This document gives schematic drawings of the assembly and operation of a wind powered water pump. The drawings are accompanied by a list of parts and materials used in the pumps manufacturing.
Publisher
Brace Research Institute
MacDonald College
McGill University
Ste. Anne de Bellevue 800
Quebec, Canada
H9X 1CO
1977
Installation
Assembly
Piston and Piston Rod
Washers and Piston Head
Operation
Parts and Materials
List of Parts and Materials
- 36 - Nut Bored at 8mm
- 34 - Round HD-Screw 4mm
- 32 - Nut 8mm
- 30 - Iron Rod 8mm
- 28 - Steel Plate 4mm
- 26 - Steel Plate 4mm
- 24 - Rubber Washer 5mm
- 22 - Rubber Washer 5mm
- 20 - Black Steel Plate 4mm
- 18 - Black Steel Plate 4mm
- 16 - Coupling 90mm/100mm
- 14 - Galv. Pipe 33mm/42mm
- 12 - Galv. Pipe 80mm/90mm