No edit summary |
No edit summary |
||
Line 10: | Line 10: | ||
#Reduce the cost of the printer by removing most of the electronics and having the computer have more direct control of the printer [[User:Bllafata|Bllafata]] ([[User talk:Bllafata|talk]]) 07:37, 3 December 2015 (PST) [[User:WayneHelminen|WayneHelminen]] ([[User talk:WayneHelminen|talk]]) 07:44, 3 December 2015 (PST) | #Reduce the cost of the printer by removing most of the electronics and having the computer have more direct control of the printer [[User:Bllafata|Bllafata]] ([[User talk:Bllafata|talk]]) 07:37, 3 December 2015 (PST) [[User:WayneHelminen|WayneHelminen]] ([[User talk:WayneHelminen|talk]]) 07:44, 3 December 2015 (PST) | ||
#Reduce waste by having none. Recycle failed prints right back into the printer with a built in recycler[[User:Bllafata|Bllafata]] ([[User talk:Bllafata|talk]]) 07:43, 3 December 2015 (PST) [[User:WayneHelminen|WayneHelminen]] ([[User talk:WayneHelminen|talk]]) 07:44, 3 December 2015 (PST) | #Reduce waste by having none. Recycle failed prints right back into the printer with a built in recycler[[User:Bllafata|Bllafata]] ([[User talk:Bllafata|talk]]) 07:43, 3 December 2015 (PST) [[User:WayneHelminen|WayneHelminen]] ([[User talk:WayneHelminen|talk]]) 07:44, 3 December 2015 (PST) | ||
#Remove atmosphere to reduce friction so that you can print faster[[User:Bllafata|Bllafata]] ([[User talk:Bllafata|talk]]) 07:47, 3 December 2015 (PST) | |||
#Remove atmosphere to improve print quality because less containments in the air[[User:Bllafata|Bllafata]] ([[User talk:Bllafata|talk]]) 07:47, 3 December 2015 (PST) | |||
#Remove hotend print with lasers [[User:Bllafata|Bllafata]] ([[User talk:Bllafata|talk]]) 07:47, 3 December 2015 (PST) | |||
#Remove extruder drive, use gravity system instead [[User:Bllafata|Bllafata]] ([[User talk:Bllafata|talk]]) 07:47, 3 December 2015 (PST) |
Revision as of 15:47, 3 December 2015
Bllafata (talk) 07:17, 1 December 2015 (PST) WayneHelminen (talk) 07:19, 1 December 2015 (PST)
- Smart slicing based on the printer, uploading the model to the printer should slice and create the gcode locally. Bllafata (talk) 07:53, 1 December 2015 (PST) WayneHelminen (talk) 07:44, 3 December 2015 (PST)
- Remove print head and use concentrated sunlight on a powder/gel to build the print WayneHelminen (talk) 07:52, 1 December 2015 (PST) Bllafata (talk) 07:32, 3 December 2015 (PST)
- Remove the motors, replace the mechanical pulley system with electromagnets to move the belt up and down. Bllafata (talk) 07:51, 1 December 2015 (PST) WayneHelminen (talk) 07:53, 1 December 2015 (PST)
- To make it safer, remove the hotend and print with foam (or other low temp materials)Bllafata (talk) 07:32, 3 December 2015 (PST) WayneHelminen (talk) 07:44, 3 December 2015 (PST)
- Subtractive 3D printing with syringe from gel WayneHelminen (talk) 07:34, 3 December 2015 (PST) Bllafata (talk) 07:37, 3 December 2015 (PST)
- Reduce the cost of the printer by removing most of the electronics and having the computer have more direct control of the printer Bllafata (talk) 07:37, 3 December 2015 (PST) WayneHelminen (talk) 07:44, 3 December 2015 (PST)
- Reduce waste by having none. Recycle failed prints right back into the printer with a built in recyclerBllafata (talk) 07:43, 3 December 2015 (PST) WayneHelminen (talk) 07:44, 3 December 2015 (PST)
- Remove atmosphere to reduce friction so that you can print fasterBllafata (talk) 07:47, 3 December 2015 (PST)
- Remove atmosphere to improve print quality because less containments in the airBllafata (talk) 07:47, 3 December 2015 (PST)
- Remove hotend print with lasers Bllafata (talk) 07:47, 3 December 2015 (PST)
- Remove extruder drive, use gravity system instead Bllafata (talk) 07:47, 3 December 2015 (PST)