This special page shows all uploaded files.
Date | Name | Thumbnail | Size | Description | Versions |
---|---|---|---|---|---|
18:32, 13 April 2011 | Shaft addition WPE.jpg (file) | 47 KB | custom shaft addition added to the windshield wiper motor used for the Waste plastic extruder drive train. | 1 | |
17:47, 13 April 2011 | Extruder FinishedHeatingZone.JPG (file) | 1.48 MB | Photo of the finished heating section. Shows Nichrome wire covered with Kapton tape. Refer to Waste plastic extruder for construction instructions. | 1 | |
17:37, 13 April 2011 | Motor brace wpe.jpg (file) | 44 KB | Used to hold the windshield wiper motor in place. Would vary with the windshield wiper motor. I used a 1994 Dodge Neon wiper motor. | 1 | |
17:35, 13 April 2011 | Flange support.jpg (file) | 43 KB | One of the plywood supports I used. These were placed at the flanges to counteract torsional forces and moments. | 1 | |
17:32, 13 April 2011 | Barrel support.jpg (file) | 42 KB | One of the plywood supports I used for the extruder body. These were placed either side of the hopper to help prevent movement axially along the barrel. | 1 | |
17:14, 13 April 2011 | Extruder DriveTrain.JPG (file) | 1.72 MB | Drive train for extruder. Shows small and large sprocket, chain and tensioning device. | 1 | |
17:12, 13 April 2011 | ExtruderMotor.JPG (file) | 1.64 MB | Motor used for waste plastic extruder. Mounted on moveable platform to allow for chain tensioning. | 1 | |
17:11, 13 April 2011 | WastePlasticExtruder prototype.jpg (file) | 1.66 MB | Picture of prototype. Doesn't include spooling device. Shows wooden base, motor and drive train and extruder body. | 1 | |
20:58, 27 March 2011 | Hopper section.jpg (file) | 59 KB | hopper section of pipe or waste plastic extruder | 1 | |
20:53, 27 March 2011 | Heating section.jpg (file) | 60 KB | Heating section of main extruder assembly. Note that piping sections were welded to the flanges. | 1 | |
20:44, 27 March 2011 | Gear section.jpg (file) | 52 KB | Gear section of main extruder body | 1 | |
20:40, 27 March 2011 | Die.jpg (file) | 46 KB | Die used to extruder 3mm filament for use in RepRap. | 1 | |
20:38, 27 March 2011 | Flange.jpg (file) | 48 KB | Flange - used to connect individual pipe sections as well as the die. Connected with fasteners. | 1 | |
20:34, 27 March 2011 | Hopper.jpg (file) | 60 KB | Hopper used on extruder. This part can be modified as needed or desired. | 1 | |
20:26, 27 March 2011 | Main body assembly.jpg (file) | 95 KB | Fixed file to show full image. | 2 | |
01:59, 23 April 2010 | Ramp Loading and FBDs.jpg (file) | 156 KB | Previous uploads were not showing file changes, hopefully this one will, | 4 | |
04:27, 2 February 2010 | Beachslack.JPG (file) | 35 KB | User page picture. | 1 | |
17:48, 24 January 2010 | Table8 kenyatrussbridge.png (file) | 19 KB | 1 |