Line 47: | Line 47: | ||
* [http://reprap.org/wiki/Heated_Bed heated bed] | * [http://reprap.org/wiki/Heated_Bed heated bed] | ||
* cut out a copper board to be used later to make heater bed and to print on | * cut out a copper board to be used later to make heater bed and to print on | ||
* Wooden bed: [http://reprap.org/wiki/Mendel_frame Mendel uses wooden base],[http://reprap.org/wiki/SGBot entire wooden mendel], [http://www.bitsfrombytes.com/fora/user/index.php?topic=127.0 wood ratings], [ | |||
* Cast Polymer: [http://reprap.org/wiki/PourStrap design 1] | |||
* General ideas: [http://reprap.org/wiki/Thermoplast_Extruder_Hints different materials and their strengths] | |||
Revision as of 19:54, 13 July 2010
Mendel Reprap Extruder Types
1) Spring Head: Allows the extruder to move over ridges that blocks its path
Instructions: No
Works:Yes
Links: [1]
2) Granular Extruder: Allows the use of pellets to make parts instead of a plastic rod
Instructions: Some, not detailed
Works:Needs Improvement
Links:[2]
[3]
3) Spool Head: prints metal, only limited shapes tested
Instructions:Some, not detailed
Works: Needs more testing on other shapes
Links:[4]
Boards for Reprap
Get all solid edge parts here:([5])
Motherboard plate
- place to mount extruder controller and motherboard
- made from MDF
- schematics
- solid edge file is located in this area in the downloaded files: reprap-mendel-20100308/mendel/mechanics/solid-models/Temporary/SolidEdge/circuit-boards motherboard-plate.par
Stepper motor mounting board:
- place to mount stepper motor drivers and usb-female pcb
- made from MDF
- schematics
- solid edge file is located in this area in the downloaded files: reprap-mendel-20100308/mendel/mechanics/solid-models/Temporary/SolidEdge/circuit-boards stepper-plate.par
Bed
- where the plastic is printed
- made from MDF
- schematics
- solid edge file is located in this area in the downloaded files: reprap-mendel-20100308/mendel/mechanics/solid-models/Temporary/SolidEdge/m4-standard-bot bed.par
other possibilities for bed:
- heated bed
- cut out a copper board to be used later to make heater bed and to print on
- Wooden bed: Mendel uses wooden base,entire wooden mendel, wood ratings, [
- Cast Polymer: design 1
- General ideas: different materials and their strengths
Y-Chassis
- set-up for the y-axis
- made from MDF
- schematics
- solid edge file is located in this area in the downloaded files: reprap-mendel-20100308/mendel/mechanics/solid-models/Temporary/SolidEdge/m4-standard-bot y-chassis.par
Purge Plate
- on the y-axis
- made from MDF
- schematics
- solid edge file is located in this area in the downloaded files: reprap-mendel-20100308/mendel/mechanics/solid-models/Temporary/SolidEdge/m4-standard-bot purge-plate.par
MDF: this needs to be 4-6mm with a 42cmx40cm sheet
Flags
- three one for each axis
- aluminum sheet, <2mm in thickness, 8cm x 5cm
- solid edge file is located in this area in the downloaded files: reprap-mendel-20100308/mendel/mechanics/solid-models/Temporary/SolidEdge/m4-standard-bot x-flag.par, y-flag.par, z-flag.par, x-flag-flat.par, y-flag-flat.par, z-flag-flat.par
Extruder Help
General Tips [6]
Reprap Parts and Where to Order
The current parts that have been ordered for the reprap are listed in this document below. I will update this document as more parts are ordered.Media:parts_for_reprap.odt
Links
- Almost totally plastic system that can move in 3 dimentions called Sarrus Linkage Mark III, and attachment for an extruder is being worked on.