{"id":64963,"key":"Obvious_3D_printer_technology_based_on_11._Cushion_in_Advance","title":"Obvious 3D printer technology based on 11. Cushion in Advance","latest":{"id":1210442,"timestamp":"2025-11-28T11:48:59Z"},"content_model":"wikitext","license":{"url":"https://www.appropedia.org/Appropedia:Copyrights","title":"CC-BY-SA-4.0"},"source":"Prepare emergency means beforehand to compensate for the relatively low reliability of an object.\n• Magnetic strip on photographic film that directs the developer to compensate for poor exposure\n• Back-up parachute\n• Alternate air system for aircraft instruments\n\nThis principle is proposed to solve the following contradictions:\n1/271/342/345/137/279/2710/1110/3411/3313/514/2714/3214/3415/2718/2819/2722/2727/427/927/1227/1427/1827/1927/2127/2227/2827/2927/3427/3828/2728/3429/2730/3532/1332/3432/3734/134/234/734/1034/1434/1534/2734/3234/3635/3037/1337/3238/27\n- See more at: http://www.triz40.com/aff_Principles_TRIZ.php#sthash.Ktouxg5P.dpuf\n\n{{777 notice}}{{TRIZ-3D}} Beforehand cushioning\n\n# Change the grease used on the guide rods to reduce the sound of the 3D printer.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:53, 1 December 2015 (PST)\n# Change the material of the print bed to a more elastic one than glass to absorb more energy[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:53, 1 December 2015 (PST)\n# '''Alter design of 3D printer to remove screws and install snapfits to allow ease of replacement of parts.'''[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:53, 1 December 2015 (PST)\n# '''Add cushions to bottom of printer to reduce vibration(sound) and improve precision.''' [[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:53, 1 December 2015 (PST)\n# Add a secondary fan system to further control the temperature control and as a back up if the primary fan fails. [[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n# add small cushions to the side of the printer for side protection.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n# Add muliple beds which can slide out from the center of the printer revealing another printer bed.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n# Change the bed screw holds to a gliding hold to allow the single print bed to be removed easily.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n# Conduct a preliminary adhesive print to act as the glue we currently use.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n## an additional print head would be helpful and a method to switch between them.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n# Add rotary printing head set up to print multiple materials.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n# Include a cleaning kit to remove built up plastic in the feeder motor.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n# Modify the guide rods to be segmented(slide into themselves) to adjust their distance from the center.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n# '''Modify Carriage to have 4 magnet slots(2 mirrored about their current position) to allow ease to switch to the motors moving a bed rather than a print head.''' [[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n# '''Switch from the wooden frame to a segmented printed hexagonal(with empty space) architecture with snap fits to allow ease of construction and packing.'''[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n## This would allow more airflow to the underside of the printer.(if the side boards were modified in this way)[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n# Add a secondary belting system to reduce the tightening of components overtime.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n# Add in a cover for the bottom of the printer, to take weight off of the 3 columns as protect the printer's brain.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:23, 3 December 2015 (PST)\n## This should still have holes in the design to promote airflow.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:33, 3 December 2015 (PST)\n# Add in fans to the base wooden design in order to cool the printer bottom more effectively.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:33, 3 December 2015 (PST)\n# Add a air system to replace the fan to control cooling to a greater degree.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:33, 3 December 2015 (PST)\n# Add a liquid cooling system for prints which need cool temperatures. [[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:33, 3 December 2015 (PST)\n# Modify connecting rods to be bent in a semicircle to allow printing on angles for more complex geometries. [[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:33, 3 December 2015 (PST)\n# '''Add a backup filament tube to switch out filaments before the filament motor. (kind of like a switch mechanism but for filaments)'''[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:37, 3 December 2015 (PST)\n# '''add a sponge like material right before the filament goes into the motor to collect dust/contamination on the filament.'''[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:37, 3 December 2015 (PST)\n# add a liquid cleaner onto the filament before it enters the feeder motor which will evaporate off upon printing.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:37, 3 December 2015 (PST)\n# '''Add a lazer sensor to the bottom of the end effector to detect the actual distance for calibration and protection of the bed purposes.''' [[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:37, 3 December 2015 (PST)\n# Add epoxy/glue to the connector plate to ensure it stays securely in the frame.[[User:Ampringl|Ampringl]] ([[User talk:Ampringl|talk]]) 07:40, 3 December 2015 (PST)\n# Add extra layer of glue to mirror so you don't scratch it [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# print bumpers for wood [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Use laser rod detection to detect if rods fall off [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Put a little extra grease on bearings [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Check mechanical parts before printing [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Add backup cooling fan [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Put protective coating over mirror so it doesn't break\n# Change wood frame to metal frame to avoid warping [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Replace printed parts with professionally made parts [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Clean your nozzle before printing [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Remove dog fur from grease (i have a dog) [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Add a filter for filament before entering extruder [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Buy a razor to remove difficult prints from bed [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Use a more powerful power supply to compensate for having to lower the fan to print at higher temperatures [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Buy extra filament so you don't run out [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Put printer next to a smoke detector if leaving it alone [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n# Print out replacement parts because the ones on the printer will fail [[User:Njlanter|Njlanter]] ([[User talk:Njlanter|talk]]) 07:50, 1 December 2016 (PST)\n\n{{Page data\n| license = CC-BY-SA-3.0\n}}\n\n[[Category:4777 TRIZ 3D printers]]"}