{"id":77912,"key":"Newspaper_briquet_maker","title":"Newspaper briquet maker","latest":{"id":1263023,"timestamp":"2026-09-02T12:20:20Z"},"content_model":"wikitext","license":{"url":"https://www.appropedia.org/Appropedia:Copyrights","title":"CC-BY-SA-4.0"},"source":"{{777 notice}}\n\n[[File:Final Maker with Briquettes.jpg|thumb]]\n\n{{Device data\n| manufacturing-files = https://www.thingiverse.com/thing:3261942\n}}\n\n{{Project data\n| authors = User:ABStilwell, User:Molson\n| years = 2018\n| made = Yes\n| replicated = Yes\n| cost = USD 9.13\n| type = Newspaper briquet maker\n}}\n\nThe need was expressed for a device in which could turn waste newspaper and other light paper products into small burnable briquettes. This helps to turn waste in to a usable fuel source, and also allows the paper to burn much longer and more efficiently than just burning the unprocessed paper.\n\n== Bill of Materials ==\n\nBOM -- Materials needed: are both 3D printed and items picked up at the local hardware store\n\n# The base, lower plate and upper crushing plate are all 3D printed and can be found on the following link\n## [https://www.thingiverse.com/thing:3261942 Thingiverse Link to Files]\n## Youmagine link coming soon!\n# The steel rod was purchased at the local hardware store, can be replaced with alternative source that can fit in 3/8 inch holes.\n# The wood handles were made from scrap wood found in the garage, and held together using 8 woods screw.\n\n== Tools needed ==\n\n# [[Athena Build Overview|MOST Delta RepRap]] or similar RepRap 3-D printer\n# Wood/Metal Saw\n# Drill or Screwdriver\n# Tape measure\n\n== Skills and knowledge needed ==\n\n* Basic Woodworking Skills\n\n== Technical Specifications and Assembly Instructions ==\n\nThe handles were made of 1x4 I had laying around and ripped it to the following dimensions.\nYou need to cut 4 pieces at 1x.75x12 inches long. On one end drill a 3/8 inch hole centered 1 inch away from the end.\nFor the ends of the handle one is 4.25 inches long and the second is 5.75 inches long, both are 1x1.5 inches.\nUsing 8-1.25 inch flat top screws anchor the tops to the handle.\n\nThe handles can be made out of any type of wood or alternate material that is approximately 12 inches long and can have a hole drilled into it to fit over the rod.\nSame goes for the Steel rod, you can replace it with anything that will fit inside a 3/8 inch hole and handle the forces from the handles being pushed down.\n\nThe assembly pictures show much longer rods than you need for the setup, you only 6 inches in length per rod.\n\nPrint Time Estimate - 14 to 16 hours dependent on printer speed and infill settings.\nAssembly time is approximately 30 minutes.\n\n<gallery>\nFile:First Combo.PNG\nFile:Simple arrow.PNG\nFile:Second Combo.PNG\nFile:Simple arrow.PNG\nFile:Third Combo.PNG\n</gallery>\n</center>\n\n=== Common Problems and Solutions ===\n\n* Be sure to not push too hard when the arms are bottomed out. This will cause the plastic to break.\n\n== Cost savings ==\n\n# Estimated Total Cost - $9.13\n\n Plastic - $6.13\n Screws - $0.50\n Wood - $1.00\n Metal Rod - $2.50\n\n# Commercial Equivalent - https://www.amazon.com/Bits-Pieces-Newspaper-Maker-Heavy-Measures/dp/B00TR0Z3X8/ref=sr_1_2?ie=UTF8&qid=1544033817&sr=8-2&keywords=newspaper+briquette+maker\n# $ Savings=$25.85 or 74%\n\n<references />\n\n{{Page data\n| keywords = 3D printing, briquets, camping, fire, newspaper, osat, recycle, plastic, wood, metal rod\n| sdg = SDG11 Sustainable cities and communities, SDG12 Responsible consumption and production\n| published = 2018\n| organizations = Michigan_Tech's_Open_Sustainability_Technology_Lab, MY4777, MTU\n| license = CC-BY-SA-3.0\n| language = en\n}}\n\n[[Category:How tos]]\n[[Category:OSAT 3D-Printable Designs]]\n[[Category:3D printing]]\n[[Category:Recycle]]\n[[Category:Plastic]]\n[[Category:Wood]]"}