Difference between revisions of "7up"
Jump to navigation
Jump to search
m (Text replacement - "contact-appropedia-user" to "authors") |
m (Text replacement - "|affiliations=Category:MTU, Category:MOST" to "|affiliations=MTU, MOST") |
||
| (7 intermediate revisions by the same user not shown) | |||
| Line 4: | Line 4: | ||
|description=Bicycle part | |description=Bicycle part | ||
|keywords=3D printing, bike part, bicycle | |keywords=3D printing, bike part, bicycle | ||
| − | | | + | |uses=hobbyism, education |
| − | | | + | |status=prototype |
|made=Yes | |made=Yes | ||
| − | | | + | |replicated=No |
|countries-of-design=United States | |countries-of-design=United States | ||
| − | | | + | |affiliations=MTU, MOST |
| − | | | + | |materials=Plastic |
|estimated-cost-amount=2.00 | |estimated-cost-amount=2.00 | ||
|estimated-cost-currency=USD | |estimated-cost-currency=USD | ||
| − | | | + | |sdg=SDG11 Sustainable cities and communities |
|contact-affiliation=MOST | |contact-affiliation=MOST | ||
|authors=User:Yanguo | |authors=User:Yanguo | ||
Latest revision as of 01:26, 5 December 2020
7up
| Description | Bicycle part |
|---|---|
| Keywords | 3D printing, bike part, bicycle |
| Uses | hobbyism, education |
| Authors | Yan Guo |
| Status | prototype |
| Made? | Yes |
| Replicated? Was this project made independently by someone other than the authors and without their guidance? | No |
| Countries of design | United States |
| Affiliations |
MTU MOST |
| Materials | Plastic |
| Estimated cost | USD $ 2.00 |
| Sustainable Development Goals | SDG11 Sustainable cities and communities |
| Instructions data | |
| Manufacturing files | https://www.appropedia.org/File:7up_1.stl |
| Documentation data | |
| Language | English |
| Manifest data | |
| Language | English |
| Updated | 2020-06-04 |
| Author | Kathy Nativi |
| Author affiliation | Appropedia |
| Author email | info@appropedia.org |
Gallery[edit | edit source]
- 777 OSAT 3-D Printable Design
Bicycle part: 7up[edit | edit source]
Project developed by Yan Guo(talk)
 |
This Open Source Appropriate Technology has been designed but not yet tested — use at your own risk. |
|
This Open Source Appropriate Technology has been prototyped. |
Abstract[edit | edit source]
- The project was offered from Dr. John Gershenson, part of his lab for measurements.
- Picture of completed print
Bill of Materials[edit | edit source]
- Only plastics and 3D-printer needed.
- link to all source files
- link to all STLs
Tools needed for fabrication of the OSAT[edit | edit source]
- MOST Delta RepRap or similar RepRap 3-D printer
Skills and Knowledge Necessary to Make the OSAT[edit | edit source]
- basic measurement
Technical Specifications and Assembly Instructions[edit | edit source]
- Print the top part and down part separately.
- Joint them by heater through the edge of each part.
- printing time for each part is about 1.5 hours.
- Jointing time is about 15 min.
Common Problems and Solutions[edit | edit source]
- Carefully when using the heater, don't burn yourself :)
Cost savings[edit | edit source]
- If your solution is not a low cost one then it is not really appropriate.
- Estimate your costs: about 2 dollar.
- Find a commercial equivalent: about 10 dollar because of the material.
- 8$ savings and 80% savings