No edit summary
Line 17: Line 17:
[[File:IMAG0049.jpg|thumb|Fig 1: The Migration hole is shown on the inside of the worm bin]]
[[File:IMAG0049.jpg|thumb|Fig 1: The Migration hole is shown on the inside of the worm bin]]


==Care and Matainance==
==How to use your Wormland Wormbin==
The bin is now ready to be filled.
# Start by putting a small amount of damp shredded news paper, a handful of dirt or dead leaves, and about a handful of food scraps (see: what to feed your worms) on only ONE side of your bin
It is necessary supply the worms the material to make their homes. These materials are referred to as bedding.  Common bedding materials include damp shredded newspaper, grass clippings, leaves, and small amounts of dirt or manure.
# Leave your worm bin for about a week or so without worms in it so that the contents of the bin can begin the decomposition process
Bedding and organic material the worms will help decompose are placed in both of the connected cartons.  Allow bedding to sit for about a week before placing the worms in their new home.  
# You may now add about a handful of worms to the side of your bin that contains the newspaper mixture.
# Once a week, use a spoon to mix up (“aerate”) the side of the bin that contains worms. Also once a week, be sure to add a small amount (about a half a handful) of food to the bin.
# After 2-3 months, the bin will start to accumulate castings (worm poop). When this starts to happen, prepare a new batch of bedding and food on the empty side of the bin. The worms will then migrate via the migration hole to where more food is provided.
# After the worms have migrated to the fresh side of the bin, you may remove the castings from the other side and use them in your gardening to produce bigger, healthier plants.


The last step is deciding what to place inside the bin. Worms love and fruit or vegetable matter, and most other organic material. Red worms
This process may continue however long you want your Wormland Worm bin to last. Due to the simple design, it is also easy to make another worm bin to replace the old one! 
enjoy breads and grains,cereal, coffee grounds and filters or tea bags,and any fruits or vegetables.
Worms will avoid dairy products, fats, meat, oils, and any feces of a carnivore or herbivore.


Once the bin is working and the worms are installed, minimal upkeep is required--make sure to keep your bin damp and your worms fed, and turn over the bedding every week to keep harmful gases produced by decomposition from building up in the bin. Also remember to collect castings periodically--when the bedding is gone and the bin is full of a dark, loamy material,the bin is now filled with nothing but castings and needs to be emptied. Replace the bin with new bedding, replace the worms, and start again!
Commence composting!


==Video==
==Video==

Revision as of 03:38, 4 May 2011

Instructions for Building Worm Bin Kids Alone

Materials needed

Two half-gallon waxed cardboard juice or milk cartons, duct tape, scissors, and several sharp pencils/pencil sharpeners.

Steps

  1. Obtain two half-gallon waxed cardboard cartons. Make sure they are rinsed out and dry before beginning to construct the worm bin.
  2. To make the migration hole for the worms between the two cartons, a 2” by 3” hole is cut into the side of each container but in the exact same location along one of the sides, so that when the two cartons are lined up the holes match exactly. To make the hole, poke four holes in the shape of a rectangle in the same location on both cartons with a sharp pencil. This makes it easier to then cut out the holes with scissors.
  3. Poke holes for ventilation and drainage along the sides and bottoms of both cartons. Three holes along the middle and five along the bottom is sufficient.
  4. Flaps are then cut into the topside of each carton, i.e. the side with the largest surface area and with the label saying “Humboldt Creamery”, etc. The same method is used as for cutting the migrations holes. Poke one hole in each corner of the top side of the carton, but cut along only three of the four connecting holes to make a flap instead of a rectangular hole.
  5. The two cartons can now be connected with duct tape. Tape the top and bottom of the cartons together lengthwise on both sides. If using cartons with flap dispensers instead of screw top spouts tape those shut as well.
  6. Finally, use more duct tape to make tabs for the worm bin’s flaps
Fig 1: The Migration hole is shown on the inside of the worm bin

How to use your Wormland Wormbin

  1. Start by putting a small amount of damp shredded news paper, a handful of dirt or dead leaves, and about a handful of food scraps (see: what to feed your worms) on only ONE side of your bin
  2. Leave your worm bin for about a week or so without worms in it so that the contents of the bin can begin the decomposition process
  3. You may now add about a handful of worms to the side of your bin that contains the newspaper mixture.
  4. Once a week, use a spoon to mix up (“aerate”) the side of the bin that contains worms. Also once a week, be sure to add a small amount (about a half a handful) of food to the bin.
  5. After 2-3 months, the bin will start to accumulate castings (worm poop). When this starts to happen, prepare a new batch of bedding and food on the empty side of the bin. The worms will then migrate via the migration hole to where more food is provided.
  6. After the worms have migrated to the fresh side of the bin, you may remove the castings from the other side and use them in your gardening to produce bigger, healthier plants.

This process may continue however long you want your Wormland Worm bin to last. Due to the simple design, it is also easy to make another worm bin to replace the old one!


Video

Error in widget YouTube: Unable to load template 'wiki:YouTube'
Cookies help us deliver our services. By using our services, you agree to our use of cookies.