Materials and Tools[edit | edit source]

File:MOST soldering material.JPG
Soldering materials.
Materials
Conductors and components
Heat shrink tubing
Solder
Flux paste
File:MOST solder tools.JPG
Necessary tools for soldering.
Tools
Soldering pen
Wire strippers
Optional - helping hand

Note[edit | edit source]

Tinning is the practice of wetting a surface with solder. In this context, it is the wetting of the exposed conductors, which is recommended as loose strands can inadvertently cause short circuits and are inherently more difficult to control than a single cohesive unit.

Video instructions[edit | edit source]

mqdefault.jpgYouTube_icon.svg
Soldering and Tinning

Step-by-step instructions[edit | edit source]

Tinning Conductor[edit | edit source]

  1. Stripped conductor twisting.
    After stripping a small amount of insulation from the end of the conductor, twist the strands together and dip into solder flux, applying a light coating of flux to the bare metal.
  2. Solder the prepared strands together.

Butt Solder Joints[edit | edit source]

All of the butt joints on the MOST Delta are located on the end effector where the heating resistor leads are connected to the power conductors and the thermistor leads and fan are connected to copper pairs. A "third hand" (either literal or the tool) greatly facilitates butt joining.

  1. Tin the conductors per instructions above.
  2. Place adequate lengths of heat shrink tubing over one of the conductors and push it away from the solder joint so it doesn't shrink during soldering.
  3. Align the tinned conductor with the conductor it is to be joined with such that the two are parallel and touching.
  4. Solder the joint and blow on it to rapidly solidify the solder.
  5. Slide the heat shrink tubing over the joint and overlapping insulators on both sides of the joint. Shrink the tube in place.

Soldering Copper Pair to Limit Switches[edit | edit source]

The limit switches have three terminals, one is common and the other two are normally open or normally closed. The controller firmware expects normally closed, which requires the conductors be soldered to the outermost two terminals, leaving the center terminal alone. Again, a "third hand" is helpful.

  1. Tin the conductors per the instructions above.
  2. Place a small solder puddle on the two outermost terminals of the limit switch.
  3. Place adequate lengths of heat shrink tubing over the conductors and push it away from the solder joint so it doesn't shrink during soldering.
  4. Soldering limit switch.
    Solder the conductors to the terminals at the puddles of solder. Blow on the joints to rapidly solidify the solder.
  5. Heat shrink tubing on limit switch.
    Slide the heat shrink tubing over the terminal and shrink in place.

Solder Extension to Fan Wires[edit | edit source]

  1. Solder extension to fan wires.
    Strip and tin both ends of a 1m length of 24ga twisted pair.
  2. If the 40mm fan has a header on the wires, snip it off with wire cutters. Strip and tin the fan wires.
  3. Cut a pair of small heat shrink tubes and slide one on each of the fan wires.
  4. Keeping the heat shrink tube away from the joint, butt solder the twisted pair to the fan wires.
  5. Move the heat shrink tubing over the solder joint and shrink in place.

Solder Power Cable to Barrel Connector[edit | edit source]

  1. The positive terminal on the barrel connector is marked.
    Strip and tin both ends of a 15cm (6 inch) length of 18ga speaker wire or lamp cord.
  2. As with the limit switches, place a small pad of solder on the positive and negative terminals of the barrel connector. The positive terminal is the largest of the three terminals.
  3. Solder the on pair of tinned ends of the speaker wire or lamp cord to the pads.

Strip and Tin Motor Wires[edit | edit source]

  1. If the motor wires come with a header attached, snip it off with wire cutters.
  2. Strip and tin the motor wires.

Navigation[edit | edit source]

FA info icon.svg Angle down icon.svg Page data
Authors Jerry Anzalone
License CC-BY-SA-3.0
Language English (en)
Translations Russian
Related 1 subpages, 24 pages link here
Impact 1,061 page views
Created October 12, 2013 by Jerry Anzalone
Modified July 7, 2022 by Kathy Nativi
Cookies help us deliver our services. By using our services, you agree to our use of cookies.