(Added galleries for cutting procedures)
(Update on the protocol, removing information on crystallinity effects.)
(29 intermediate revisions by the same user not shown)
Line 1: Line 1:
{{MOST}}
{{MOST}}
[[category:MOST methods]]
[[category:MOST methods]]
{{Template:Status-Model}}
'''THIS METHOD IS CURRENTLY  A WORK IN PROGRESS'''
'''THIS METHOD IS CURRENTLY  A WORK IN PROGRESS'''


Line 16: Line 17:
===Shredding and Cleaning: General Procedure===
===Shredding and Cleaning: General Procedure===
# Peel any labels and/or different colored plastics off of the bottle.
# Peel any labels and/or different colored plastics off of the bottle.
# Remove any glue from the wrappings off using your cleaner. MOST used => TESTING IN PROGRESS.
# Remove any glue from the wrappings off using your cleaner. MOST used => Duct tape. The sticky side, if repeatedly applied and removed, can pull of the glue. This process, however, takes a significant amount of time.
# Rinse out your container, and dry, to remove any leftover beverages.
# Rinse out your container, and dry, to remove any leftover beverages.
# Cut apart bottles and containers to fit into your shredder. The threaded section will most likely need to be removed, until a total-shredder is developed.
# Cut apart bottles and containers to fit into your shredder. The threaded section will most likely need to be removed, until a total-shredder is developed.
# Shred the PET chunks. MOST has used a "Chipper Joe", green wood-chipper and a disk shredder, from Staples. The disk shredder has worked the best so far, with consistent results. The wood chipper is not great for water bottles, it regularly becomes jammed, and has inconsistent sizes.
# Shred the PET chunks. MOST has used a "Chipper Joe", green wood-chipper and a disk shredder, from Staples. The disk shredder has worked the best so far, with consistent results. The wood chipper is not great for water bottles, it regularly becomes jammed, and has inconsistent sizes.
# Collect the chunks and store somewhere cool and dry until the re-crystallization step, just as a preventative measure to moisture buildup.
# Collect the chunks and store somewhere cool and dry until the drying step, just as a preventative measure to moisture buildup.


===Cutting Techniques===
===Cutting Techniques===
Line 26: Line 27:


====Method 1 (Gatorade Bottles): Tested====
====Method 1 (Gatorade Bottles): Tested====
#cut apart the bottle as shown in pictures.
#Cut apart the bottle as shown in pictures.
##top and bottom off
##Top and bottom off
##cut in half
##Cut in half
##trim curved pieces
##Trim off curved pieces
#Plug in and turn on disk shredder (NW corner of room)
#Plug in and turn on disk shredder (NW corner of room)
#Hold forwards button
#Hold forwards button
#Insert slightly curved section into disk shredder.
#Insert slightly curved section into disk shredder.
#Losses of:
#Losses of 14/24g:
#*the thread
#*The thread
#*bottom
#*Bottom
#*curved top
#*Curved top


<gallery mode=packed>
<gallery mode=packed>
Line 45: Line 46:
</gallery>
</gallery>


====Method 2 (Gatorade Bottle): Untested====
====Method 2 (Gatorade Bottle): Tested====
NOTE: At MOST this doesn't really work, as the bottles decompress inside the wood chipper and jam.
#Cut off top and bottom
#Cut off top and bottom
#cut 1 slit in bottle lengthways
#Cut 1 slit in bottle lengthways
#Turn on wood chipper
#Turn on wood chipper
#compress and slide into wood chipper
#compress and slide into wood chipper
#Losses of:
#Losses of 10/24g:
#*the thread
#*The thread
#*bottom
#*Bottom


<gallery mode=packed>
<gallery mode=packed>
Line 65: Line 67:
#Insert sections lengthways
#Insert sections lengthways
#Losses of:
#Losses of:
#*the thread
#*The thread


<gallery mode=packed>
<gallery mode=packed>
File:
File:PETBottleM3_1.jpg|Cut the top of the bottle off.
File:
File:PETBottleM3_2.jpg|Cut the bottle into two halves. The base may be difficult to cut, as it is much thicker.
File:
File:PETBottleM3_3.jpg|Cut the halves now, so that you have 4 quarters of the bottle.
File:
</gallery>
</gallery>


==Recrystallization==
====Method 4 (Water Bottle Threads): Tested====
Amorphous PET retains more water than crystalline PET, and also tends to clump together when dried. Temperaturesfor drying are intended to be for crystalline PET, rather than the amorphous form. Because of these factors, the amorphous PET which is collected from beverage bottles needs to be recrystallized first.
#Place a large plastic container under the output of the wood chipper. Alternatively, a cardboard box may be used, but pieces of the plastic may be lost in the seams of the box.
#Take the threads from the water bottles that none of the other methods can shred.
#Turn on the wood chipper, and WEAR SAFETY GLASSES.
#Carefully insert them into the wood chipper.
#Turn off the wood chipper when done, and collect the results.
#Losses of:
#*None, as we are able to use the losses of a previous method.
 
<gallery mode=packed>
File:PETBottleM4_1.jpg|Carefully insert the tops of the bottles into the wood chippers. Never put your hands inside the wood chipper.
</gallery>


Currently, the reccommended method of doing this is to agitate and heat the amorphous shredded plastic at 180°F for around 1 hour [http://www.ptonline.com/knowledgecenter/Plastics-Drying/Resin-Types/Crystalline-vs-Amorphous-PET]. This will increase the crystallinity of the plastic, and prepare it for drying.
==[[Polymer drying protocol:MOST|PET Drying]]==
==Drying==
PET needs to be dried prior to extrusion in a [[Recyclebot]] as otherwise it will undergo rapid hyrdolyzation at high temperatures, and reduce the molecular mass.
PET needs to be dried prior to extrusion in a [[Recyclebot]] as otherwise it will undergo rapid hyrdolyzation at high temperatures, and reduce the molecular mass.
===Drying: Equipment===
*Convection Drying Oven (Any oven will generally work, ovens at home run off the same convection principles of heating and moving air. If using a home oven, be careful of temperatures, and be aware that there could potentially be burning plastic inside of it, if proper precautions are not taken)
*Shredded PET
*Drying tray (Any metal tray to hold the PET shreds)
===Drying: Procedure===
# Turn on the oven
# Evenly distribute the shredded PET in the drying tray. This exposes more surface area to enhance evaporation speed.
# Open the oven by firmly opening the door. It may take a quick jerk, but be careful not to topple it.
# Place the tray inside the oven.
# Close the oven door, firmly.
# Set the temperature on your oven to a value as shown by the table below. This table is a work in progress, please feel free to contribute and check!
# Wait for an amount of time also shown in the table above.
# Switch off the oven then carefully open the door after letting it cool for a few minutes.
# Quickly place the PET in an airtight container, such as inside two (2) layers of plastic bags that are twisted and tied shut. As long as the PET is not allowed to reabsorb water from the air, any arrangement will work.
# Store PET in a cool dry place until it is to be used. One excellent method is to place the dry PET inside a bag, which also has dessicant. This further dries the plastic, and will remove any moisture that may have accrued whilst handling it.
===Temperature and Time Table===
Important temperatures to be mindful of: 260°C is the melting point. 70-80°C is the glass transition temperature. The PET MUST be crystalline before this point, otherwise, temperatures much above the T<sub>g</sub> will just clump the plastic together and cause it to degrade.
{| border="1"
|-
|
! 1 Hour
! 2 Hours
! 3 Hours
! 4 Hours
! 5 Hours
! 6 Hours
|-
! 82°C
Slightly above T<sub>g</sub>
| No Change
| No change
|
|
|
|
|-
! 100°C
|
|
|
|
|
|
|-
! 125°C
|
|
|
|
|
|
|-
! 150°C
|
|
|
|
|
|
|-
! 175°C
|
|
|
|
|
|
|-
! 200°C
|
|
|
|
|
|
|-
! 225°C
|
|
|
|
|
|
|-
! 250°C
|
|
|
|
|
|
|-
! 275°C
|
|
|
|
|
|
|-
! 300°C
|
|
|
|
|
|
|}

Revision as of 00:04, 14 March 2016

Template:Status-Model THIS METHOD IS CURRENTLY A WORK IN PROGRESS

Here is outlined the method to shred, clean and dry PET at the MOST lab at Michigan Technological University. For more information on PET mechanisms please see the PET Extrusion literature review.

Shredding and Cleaning

Any PET bottles or containers which are to be to be recycled need to be ground up into smaller pieces first. This is to speed up the drying process, and also, to fit the plastic into the RecycleBot hopper. Approximately 1/4 of the mass of an average water bottle is in the thred and cap region of the main body. This is because this region has to be very resistant to deformation so that the cap can correctly screw on.

The leftover glue from the label on this water bottle.

Shredding and Cleaning: Equipment

  • Shredder
  • Oil-based cleaner to remove glue, see step 2. Peanut butter, nail polish remover, and perfume are all recommended. (NO WD40)
  • Scissors or shears

Shredding and Cleaning: General Procedure

  1. Peel any labels and/or different colored plastics off of the bottle.
  2. Remove any glue from the wrappings off using your cleaner. MOST used => Duct tape. The sticky side, if repeatedly applied and removed, can pull of the glue. This process, however, takes a significant amount of time.
  3. Rinse out your container, and dry, to remove any leftover beverages.
  4. Cut apart bottles and containers to fit into your shredder. The threaded section will most likely need to be removed, until a total-shredder is developed.
  5. Shred the PET chunks. MOST has used a "Chipper Joe", green wood-chipper and a disk shredder, from Staples. The disk shredder has worked the best so far, with consistent results. The wood chipper is not great for water bottles, it regularly becomes jammed, and has inconsistent sizes.
  6. Collect the chunks and store somewhere cool and dry until the drying step, just as a preventative measure to moisture buildup.

Cutting Techniques

Some containers may be made of a thicker plastic than others, so different methods must be taken to prepare them.

Method 1 (Gatorade Bottles): Tested

  1. Cut apart the bottle as shown in pictures.
    1. Top and bottom off
    2. Cut in half
    3. Trim off curved pieces
  2. Plug in and turn on disk shredder (NW corner of room)
  3. Hold forwards button
  4. Insert slightly curved section into disk shredder.
  5. Losses of 14/24g:
    • The thread
    • Bottom
    • Curved top

Method 2 (Gatorade Bottle): Tested

NOTE: At MOST this doesn't really work, as the bottles decompress inside the wood chipper and jam.

  1. Cut off top and bottom
  2. Cut 1 slit in bottle lengthways
  3. Turn on wood chipper
  4. compress and slide into wood chipper
  5. Losses of 10/24g:
    • The thread
    • Bottom

Method 3 (Plastic Water bottle): Tested

  1. Cut top off of bottle
  2. Split into 4 sections
  3. Plug in and turn on disk shredder, in NW corner of room
  4. Hold forwards button
  5. Insert sections lengthways
  6. Losses of:
    • The thread

Method 4 (Water Bottle Threads): Tested

  1. Place a large plastic container under the output of the wood chipper. Alternatively, a cardboard box may be used, but pieces of the plastic may be lost in the seams of the box.
  2. Take the threads from the water bottles that none of the other methods can shred.
  3. Turn on the wood chipper, and WEAR SAFETY GLASSES.
  4. Carefully insert them into the wood chipper.
  5. Turn off the wood chipper when done, and collect the results.
  6. Losses of:
    • None, as we are able to use the losses of a previous method.

PET Drying

PET needs to be dried prior to extrusion in a Recyclebot as otherwise it will undergo rapid hyrdolyzation at high temperatures, and reduce the molecular mass.

Cookies help us deliver our services. By using our services, you agree to our use of cookies.