(16 intermediate revisions by the same user not shown)
Line 2: Line 2:
<!-- These comments are offered as an aid as you get started. Remove as you wish. -->
<!-- These comments are offered as an aid as you get started. Remove as you wish. -->
<!-- next line is the code for inserting an image; delete if you don't have an image yet -->
<!-- next line is the code for inserting an image; delete if you don't have an image yet -->
[[File:Imageneeded.png|thumb|right|Sample photo caption.]]


<center>''This project was first designed to upgrade a salt spray chamber on Michigan Technological Universities campus. The project has been expanded to upload all designs of the salt spay chamber to open source design. ''</center>
<center>''This project was first designed to upgrade a salt spray chamber on Michigan Technological Universities campus. The project has been expanded to convert all designs of the salt spay chamber to open source design. ''</center>


== Project goals ==
== Project goals ==
Line 24: Line 23:
|lines=5
|lines=5
|Image:Nozzle_clamp.PNG|[http://3dprint.nih.gov/discover/3dpx-002137 Nozzle Clamp]
|Image:Nozzle_clamp.PNG|[http://3dprint.nih.gov/discover/3dpx-002137 Nozzle Clamp]
|Image:Insulation_bracket.PNG|[http://3dprint.nih.gov/discover/3dpx-002140 Insulation Bracket]
|Image:Insulation_bracket.PNG|[http://3dprint.nih.gov/discover/3DPX-002169 Insulation Bracket]
|Image:Coupon_rack.PNG|[http://3dprint.nih.gov/discover/3dpx-002139 Coupon Rack]
|Image:Coupon_rack.PNG|[http://3dprint.nih.gov/discover/3dpx-002139 Coupon Rack]
|Image:Hood_prop.PNG|[http://3dprint.nih.gov/discover/3dpx-002150 Hood Props]
|Image:Hood_prop.PNG|[http://3dprint.nih.gov/discover/3dpx-002150 Hood Props]
|Image:Chamber_drain.png|[http://3dprint.nih.gov/discover/3DPX-002161 Chamber Drain]
|Image:Chamber_drain.png|[http://3dprint.nih.gov/discover/3DPX-002161 Chamber Drain]
}}
{{Gallery
|width=180
|height=135
|title= Before and After
|lines=2
|Image:Before_chamber.jpg|Before
|Image:After_chamber.jpg|After
}}
{{Gallery
|width=180
|height=135
|title= Insulation Clamp
|lines=3
|Image:Insulation_bracket_1.jpg|Side View
|Image:Insulation_bracket_2.jpg|Front View
|Image:Bracket_clamping.jpg|In Use
}}
{{Gallery
|width=180
|height=135
|title= Hood Prop
|lines=1
|Image:Hood_prop_1.jpg|Printed Hood Prop
}}
}}


Line 44: Line 70:
|title= Nozzle Images
|title= Nozzle Images
|lines=1
|lines=1
|Image:Nozzle_clamp_1.jpg|Nozzle in Chamber
|Image:Nozzle_clamp_1.jpg|Nozzle with Clamp
}}
}}


Line 57: Line 83:
== Costs ==
== Costs ==


You may describe your costs here.
This table shows the cost savings for the current modifications to the chamber.
{| class="wikitable"
{| class="wikitable"
|-
|-
Line 66: Line 92:
! Hood Props
! Hood Props
! Chamber Drain
! Chamber Drain
! TOTAL
|-
|-
| Original Price
! Original Price
| $5
| $5
| $30
| $30
| $100
| $400 for 4
| $60
| $60
| $10
| $10
| $505
|-
|-
| New Price
! New Price
| <<$1
| <<$1
| $16 for 16
| $16 for 16
Line 80: Line 108:
| $11.30
| $11.30
| <<$1
| <<$1
| $33
|-
|-
| Savings
! Savings
| $5
| $5
| $14
| $14
Line 87: Line 116:
| $48.70
| $48.70
| $10
| $10
! $472
|}
|}
== Next steps ==
Publish detailed instructions.


== Conclusions ==
== Conclusions ==


This salt spray chamber would save approximately $19,000 from our first rough estimates. Our current modifications now save $475 assuming that just 4 sample racks are needed. These modifications can easily be put into most chambers with only small changes needed. This chamber has no loss in quality, and currently complies with all ASTM standards.
This salt spray chamber would save approximately $19,000 from our first rough estimates. Our current modifications now save approximately $475 assuming that just 4 sample racks are needed. These modifications can easily be put into most chambers with only small changes needed. This chamber has no loss in quality, and currently complies with all ASTM standards.


== Project Members ==
== Project Members ==


Cleyton Cavallaro,
[[User:Cleyton|Cleyton Cavallaro]],
Eli Gooding,
[[User:Thomas_Korejsza|Thomas Korejsza]],
Thomas Korejza,
[[User:Eli_Gooding|Eli Gooding]],
Erik Bain,
[[User:Erik_Bain|Erik Bain]],
Mike Holt,
[[User:mdholt|Mike Holt]],
Kyle Barie
[[User:klbarie|Kyle Barie]]


<!-- Don't change the next line unless you intend to change the categorization -->
<!-- Don't change the next line unless you intend to change the categorization -->
<!-- Do add additional, appropriate categories.  See http://www.appropedia.org/Appropedia:CategoryTree for ideas. -->
<!-- Do add additional, appropriate categories.  See http://www.appropedia.org/Appropedia:CategoryTree for ideas. -->
[[Category:Projects]]
[[Category:Projects]]
[[Category:MY4777]]

Revision as of 17:29, 10 November 2015


This project was first designed to upgrade a salt spray chamber on Michigan Technological Universities campus. The project has been expanded to convert all designs of the salt spay chamber to open source design.

Project goals

  1. Plan upgrades
  2. Execute Upgrades
  3. Make BOM and instructions for entire chamber
  4. Profit

Design

All design files are hosted on http://3dprint.nih.gov The links for each file are listed below.

Costs

This table shows the cost savings for the current modifications to the chamber.

Nozzle Clamp Insulation Bracket Coupon Rack Hood Props Chamber Drain TOTAL
Original Price $5 $30 $400 for 4 $60 $10 $505
New Price <<$1 $16 for 16 <<$1 each $11.30 <<$1 $33
Savings $5 $14 $100 $48.70 $10 $472

Conclusions

This salt spray chamber would save approximately $19,000 from our first rough estimates. Our current modifications now save approximately $475 assuming that just 4 sample racks are needed. These modifications can easily be put into most chambers with only small changes needed. This chamber has no loss in quality, and currently complies with all ASTM standards.

Project Members

Cleyton Cavallaro, Thomas Korejsza, Eli Gooding, Erik Bain, Mike Holt, Kyle Barie

Cookies help us deliver our services. By using our services, you agree to our use of cookies.