No edit summary |
No edit summary |
||
| Line 55: | Line 55: | ||
|- | |- | ||
|<div id="idler_end">[[File:OSHE_Growbot_Electrical_TopCap.PNG|thumb|300px|center|'''Top Cap''']]</div> | |<div id="idler_end">[[File:OSHE_Growbot_Electrical_TopCap.PNG|thumb|300px|center|'''Top Cap''']]</div> | ||
| | |Top cover of soil sensor that aids in keeping water-tight seal | ||
|1 | |1 | ||
|- | |- | ||
|<div id="idler_end">[[File:OSHE_Growbot_Electrical_BottomCap.PNG|thumb|300px|center|'''Bottom Cap''']]</div> | |<div id="idler_end">[[File:OSHE_Growbot_Electrical_BottomCap.PNG|thumb|300px|center|'''Bottom Cap''']]</div> | ||
| | |Bottom cover of soil sensor that aids in keeping water-tight seal | ||
|1 | |1 | ||
|- | |- | ||
|<div id="idler_end">[[File:OSHE_Growbot_Glossary_Bearing.png|thumb|300px|center|'''Bearing''']]</div> | |<div id="idler_end">[[File:OSHE_Growbot_Glossary_Bearing.png|thumb|300px|center|'''Bearing''']]</div> | ||
| | |PETG Bearing located in sensor rack cover | ||
|1 | |1 | ||
|- | |- | ||
|<div id="idler_end">[[File:OSHE_Growbot_Glossary_MotorMountNEMA11.png|thumb|300px|center|'''Motor Mount''']]</div> | |<div id="idler_end">[[File:OSHE_Growbot_Glossary_MotorMountNEMA11.png|thumb|300px|center|'''Motor Mount''']]</div> | ||
| | |Mount for soil sensor motor | ||
|1 | |1 | ||
|- | |- | ||
|<div id="idler_end">[[File:OSHE_Growbot_Glossary_PinionGear.png|thumb|300px|center|'''Pinion Gear''']]</div> | |<div id="idler_end">[[File:OSHE_Growbot_Glossary_PinionGear.png|thumb|300px|center|'''Pinion Gear''']]</div> | ||
| | |Drive gear for soil sensor asssmebly | ||
|1 | |1 | ||
|- | |- | ||
|<div id="idler_end">[[File:OSHE_Growbot_Glossary_Rack.png|thumb|300px|center|'''Sensor Rack''']]</div> | |<div id="idler_end">[[File:OSHE_Growbot_Glossary_Rack.png|thumb|300px|center|'''Sensor Rack''']]</div> | ||
| | |Rack of assmebly that holds soil sensor and articulates down from Growbot | ||
|1 | |1 | ||
|- | |- | ||
|<div id="idler_end">[[File:OSHE_Growbot_Glossary_SensorRackCover.png|thumb|300px|center|'''Sensor Rack Cover''']]</div> | |<div id="idler_end">[[File:OSHE_Growbot_Glossary_SensorRackCover.png|thumb|300px|center|'''Sensor Rack Cover''']]</div> | ||
| | |Cover for sensor rack components | ||
|1 | |1 | ||
|- | |- | ||
|<div id="idler_end">[[File:OSHE_Growbot_Glossary_SensorRackTrack.png|thumb|300px|center|'''Sensor Rack Track''']]</div> | |<div id="idler_end">[[File:OSHE_Growbot_Glossary_SensorRackTrack.png|thumb|300px|center|'''Sensor Rack Track''']]</div> | ||
| | |Track for rack articulation | ||
|1 | |1 | ||
|- | |- | ||
Revision as of 01:24, 7 May 2020
This page is a photographic glossary of all of the 3D printed parts for the Growbot. All files can be found on our OSF repository. All parts were printed on a Prusa MK3s with black Atomic Filament PETg, infill was 20% and 0.2mm layer height.
| Part | Description | Count |
|---|---|---|
 |
Drive gear located on motor shaft. Inserted with a 3mm hex nut and bolt on side mount to tighten unit to the shaft. | 2 |
 |
Driven Gear located on axle assembly. Attached to wheel via 3mm hex nuts and bolts, compressed together within axle assembly. | 4 |
 |
Wheel located on the end of the axle assembly. Joins to the 72-tooth gear and is base for tire to mount onto. | 4 |
 |
NinjaFlex Tire with custom treads. Mounts onto wheel by sliding over ridges and held in place via friction. | 4 |
 |
Bearing Carrier for the entire axle assembly and is bolted directly into the aluminium extrusion via t-nuts. | 4 |
 |
Motor mount located on either side of GrowBot. Base for encoder mounts and support torque driven through the chassis. | 2 |
 |
Encoder Mounts on the end of both motors. Mount directly to the the motor mounts via 3mm bolts and heat inserted nuts. | 2 |
 |
E-Stop mount for easy access to disable robot movement in case of an emergency. | 1 |
 |
Rack and Pinion carrier for water sensor located on the outside of the Growbot. | 1 |
 |
Standoffs located on rear section of motor mounts to aid in connection to chassis. | 4 |
 |
Battery carrier that sits inside GrowBot chassis, bolts up directly to bottom plate. | 1 |
 |
Top cover of soil sensor that aids in keeping water-tight seal | 1 |
 |
Bottom cover of soil sensor that aids in keeping water-tight seal | 1 |
 |
PETG Bearing located in sensor rack cover | 1 |
 |
Mount for soil sensor motor | 1 |
 |
Drive gear for soil sensor asssmebly | 1 |
 |
Rack of assmebly that holds soil sensor and articulates down from Growbot | 1 |
 |
Cover for sensor rack components | 1 |
 |
Track for rack articulation | 1 |
