(Created page with "{{777}} == Hanging Garden == Project developed by [[User:Oacreame | Olivia Creamer] {{Statusboxtop}} {{status-design}} {{status-prototype}} You can help Appropedia by contrib...") |
No edit summary |
||
Line 11: | Line 11: | ||
The purpose of this design is to allow people to grow fruits, vegetables, and herbs close to their home with minimal space and water usage. The basic design are buckets that can be suspended by any rope over each other with holes in the bottom to allow excess water in each bucket to spill through and water the next plant below. THis design will allow people in contries with limited space and water to still be able to have a small garden to help provide food for their family. This garden also allows for the growth of flowers and other plants to decorate any house. | The purpose of this design is to allow people to grow fruits, vegetables, and herbs close to their home with minimal space and water usage. The basic design are buckets that can be suspended by any rope over each other with holes in the bottom to allow excess water in each bucket to spill through and water the next plant below. THis design will allow people in contries with limited space and water to still be able to have a small garden to help provide food for their family. This garden also allows for the growth of flowers and other plants to decorate any house. | ||
[[Image:SideViewOfPot.JPEG|200px|right]] | |||
== Bill of Materials== | == Bill of Materials== | ||
Line 29: | Line 29: | ||
|- | |- | ||
|} | |} | ||
All files can be found at: [https://www.youmagine.com/designs/hanging-garden-that-conserves-water YouMagine] | |||
== Tools needed for fabrication of the OSAT== | == Tools needed for fabrication of the OSAT== | ||
Line 36: | Line 35: | ||
== Technical Specifications and Assembly Instructions== | == Technical Specifications and Assembly Instructions== | ||
# Print as many buckets as desired using any hard filament keeping in mind that each bucket will take around | # Print as many buckets as desired using any hard filament keeping in mind that each bucket will take around 8 hours and 30 minutes to print | ||
# Cut a section of rope that allows space for the amount of buckets printed plus the plant that will be growing in it | # Cut a section of rope that allows space for the amount of buckets printed plus the plant that will be growing in it | ||
# Thread the rope through the holes on the sides of the bucket from inside to outside and tie a tight knot on the outside of each side making sure the bucket will hang level | # Thread the rope through the holes on the sides of the bucket from inside to outside and tie a tight knot on the outside of each side making sure the bucket will hang level | ||
Line 43: | Line 42: | ||
# Water top plant as often as needed allowing excess to drip to lower pots. | # Water top plant as often as needed allowing excess to drip to lower pots. | ||
depending on amount of buckets the total time to assemble and plant plants in the buckets should be less than an hour | depending on amount of buckets the total time to assemble and plant plants in the buckets should be less than an hour | ||
=== Common Problems and Solutions=== | === Common Problems and Solutions=== | ||
Line 57: | Line 53: | ||
== Benefited Internet Communities == | == Benefited Internet Communities == | ||
* OSAT: [https://www.appropedia.org/Open_Source_Appropriate_Technology] | * OSAT: [https://www.appropedia.org/Open_Source_Appropriate_Technology] | ||
* | * YouMagine [https://www.youmagine.com/] | ||
* Thingiverse [https://www.thingiverse.com/] | * Thingiverse [https://www.thingiverse.com/] | ||
[[Category:OSAT 3D-Printable Designs]] | [[Category:OSAT 3D-Printable Designs]] |
Revision as of 03:19, 5 December 2019
Hanging Garden
Project developed by [[User:Oacreame | Olivia Creamer]
Template:Statusboxtop Template:Status-design Template:Status-prototype You can help Appropedia by contributing to the next step in this OSAT's status. Template:Boxbottom
Abstract
The purpose of this design is to allow people to grow fruits, vegetables, and herbs close to their home with minimal space and water usage. The basic design are buckets that can be suspended by any rope over each other with holes in the bottom to allow excess water in each bucket to spill through and water the next plant below. THis design will allow people in contries with limited space and water to still be able to have a small garden to help provide food for their family. This garden also allows for the growth of flowers and other plants to decorate any house.
Bill of Materials
Part | Price | Quantity |
---|---|---|
Any 3D Filament | $15.00 - $20.00 | 1 |
Any Rope | $5.00 - $10.00 | 1 |
All files can be found at: YouMagine
Tools needed for fabrication of the OSAT
- MOST Delta RepRap or similar RepRap 3-D printer
Technical Specifications and Assembly Instructions
- Print as many buckets as desired using any hard filament keeping in mind that each bucket will take around 8 hours and 30 minutes to print
- Cut a section of rope that allows space for the amount of buckets printed plus the plant that will be growing in it
- Thread the rope through the holes on the sides of the bucket from inside to outside and tie a tight knot on the outside of each side making sure the bucket will hang level
- Plant desired fruits, vegetables, herbs, or flowers within the pots
- Hang the garden by tying the top of the rope to the rafters or a curtain rod
- Water top plant as often as needed allowing excess to drip to lower pots.
depending on amount of buckets the total time to assemble and plant plants in the buckets should be less than an hour
Common Problems and Solutions
- If the buckets are hung on the rope too close together there may not be enough room for the plant to grow. Be sure to be conscious of the type of plant going in each bucket and plan spacing accordingly
Cost savings
- Cost of the print: less than $2 per bucket
- Cost of rope: Less than $10 per roll
- There is no commercial equivalent with the water saving technology as of December 2019