Line 78: Line 78:
[https://polarisstarpower.com/forums/ polarisstarpower]
[https://polarisstarpower.com/forums/ polarisstarpower]


==References==
===References===
 
* The sources of information (e.g. engineering handbooks, journal articles, government documents, webpages, books, magazine articles etc.). References should use the <nowiki> <ref> </ref> and <references/>  </nowiki>tags and can be in any format but should include all the information necessary for someone else to find the same information you did. For example: <ref> web page: Department of Energy (DOE) Landscaping and Energy Efficiency, DOE/GO-10095 (1995) Available: http://www.eren.doe.gov/erec/factsheets/landscape.html</ref>
 
<references/>
<nowiki>
Based on the developmental needs addressed (e.g. food, heat, electricity, clean water, health  care, etc.) be sure to label your device in the proper categories e.g. use [[Category:Water]]. Be sure to categorize your device so that it will be easy to find – for example “Low voltage connection basics” is categorized in
 
[[Category:How tos]]
[[Category:Electricity]]
[[Category:Electric lighting]].
 
</nowiki>


[[category:OSAT 3D-Printable Designs]]
[[category:OSAT 3D-Printable Designs]]

Revision as of 20:29, 4 December 2019

This page was part of an MTU course MSE4777 OA and MSE4777 OB/MSE5777/EE4777/EE5777: Open-source 3-D printingPlease leave comments using the talk page. The course runs in the Fall semester. It is not open edit.Read more...

Fuel Container Restraint

Project developed by Trfranck

Template:Statusboxtop Template:Status-prototype You can help Appropedia by contributing to the next step in this OSAT's status. Template:Boxbottom

Abstract

  1. Paragraph description of the OSAT - why is it Appropriate? What need does it fulfil? Are there case studies you have found of a technology being used successfully?
  2. Picture of completed print using your printer
    Wood WorkingClamp Parts.png

Bill of Materials

  1. Provide a full BOM -- Materials needed for fabrication of device and alternative materials if they are not available, prices/sources of non-printable parts
    1. Upload and link to all source files from open source CAD
    2. Upload and link to all STLs

Tools needed for fabrication of the OSAT

  1. MOST Delta RepRap or similar RepRap 3-D printer

Skills and Knowledge Necessary to Make the OSAT

  • Knowledge of Using Fasteners
    • Installation - Screw, Rivet, Bolt

Technical Specifications

Print Instructions

  • Print time estimate - 8.5hrs (Printing all four pieces at once)
  1. To ensure proper bed adhesion, the use of a brim or a raft is recommended. I had good results with a brim of 2mm.

Support material is not required.

Assembly Instructions

  • Assembly time estimate - 1hr (Dependant on fastener type)


Center
1. To determine the placement of the mounts, the container intended to be used is needed. 

Center
2. Place the container in the desired location

Center
3.  Use a straight edge and mark the edges of the container across the surface. This will help with step 10 to align the remaining corner pieces.

Center
4.  Place one of the Fuel Container Restraint pieces at one of the corners of the container.

Center
5. The use of a straight edge is recommended to ensure symmetric alignment. Measure the distance 

Center
6. Gently lift the container.

Center
7. Mark where the mounting holes are located with a marker.

Center
8. Remove the Fuel Container Restraint piece and drill out the marked holes.

Center
9. Use the desired fastener to secure the Fuel Container Restraint piece to the surface.

10. Repeat steps 4-9 for the remaining three pieces.

Cost savings

Benefited Internet Communities

  • Name and add links to at least 5 using single brackets around [url name]

ty4stroke arcticchat polarisstarpower

References

Retrieved from "https://www.appropedia.org/w/index.php?title=Fuel_Container_Restraint&oldid=397775"
Cookies help us deliver our services. By using our services, you agree to our use of cookies.