No edit summary
Line 1: Line 1:
[[Category:Hexayurt project]]
This page ''may'' end up after [[Hexayurt_playa#Partial_Folding_Hexayurt]] but we're working here for clarity and because there are many pictures.
This page ''may'' end up after [[Hexayurt_playa#Partial_Folding_Hexayurt]] but we're working here for clarity and because there are many pictures.



Revision as of 09:54, 2 May 2011


This page may end up after Hexayurt_playa#Partial_Folding_Hexayurt but we're working here for clarity and because there are many pictures.

Also THIS IS A RAW UPLOAD OF NON "BETA-TESTED" INSTRUCTIONS, SO PLEASE USE WITH CARE, OR ONLY IN MODELS, UNTIL THEY ARE REVIEWED. THANK YOU & DON'T SAY YOU HAVEN'T BEEN WARNED! LucasG 10:28, 1 May 2011 (PDT)

Camp-Danger Two-Part Folding Hexayurt

What it is

This is a variation for a folding hexayurt. If the 4'x8' panels you use are XXX" thick, you end up with a XXX" thick stack that you can truck to the Playa and back. You do most of the work at home, and setting it up takes much less time and hassle. Do you also need less people?

Designers

Design and instructions by Julie Danger and Chris Camp, at Burning Man 2010 (or earlier).

Video

  • Short video showing how it's unfolded and folded back, speeded up a bit.
  • Maybe add a timelapse video showing the whole procedure in 1 minute.

Advantages

  • it's foldable!
  • time in general
  • time and hassle at the playa
  • you save tape

It will save you tape, it will save you time, and 90% of the work will already be done when you get to the playa. You will skip all the difficult and labor-intensive steps of "constructing the roof cone" (that part is difficult, especially in the elements of the Black Rock desert: wind, dust, sun, heat.) Your roof cone will be in two halves that accordion-fold open, your walls will be in two halves as well. You will not need to do any fancy cutting or need any extra materials, and you will have a 1x4x8 foot stack of panels to transport, as usual. (Note: these instructions are for the "8 foot hexayurt design," using rigid insulation. They can be utilized for other designs as well.)

  1. Stop here-- the semi-folding design uses less tape. Usually you seal all panel edges with tape. This adds strength and protects the playa from moop, but in this design the hinges provide part of the sealing. Here you will tape-seal only certain edges: the 'bases' (2" edges) of all of the triangular roof panels. Optional: tape just the "tips" of the roof panels for reinforcement. The best way of doing this is to start the tape about 2-3" from the edge you're sealing. See image below. There is a trick to keeping the tape tidy at the corners if you feel perfectionistic-- see the video.
  2. ((( DON'T Now do the same for the 6 boards you are using for the walls.))) Tape the 8 foot edges on all the rectangular wall panels--but do not tape the 4" sections yet.

Step By Step Instructions

The sequence is you buy stuff, make the hexayurt at home, fold it, take it to the Playa, unfold it, fix it to the ground, maybe add some good-to-haves, live in it, fold it again, take it back home.

(for each step, number of people needed) (for each step, numbers of pictures: 1, 2-4, 5 ... or whatever)

Things to buy

buy panels, tape, cutter, masks, gloves

volume of the stack you need to take home varies depending on thickness of panels

Cut half of the panels in half, diagonally

At home, prepare the panels. This is best done with two people.

cut 6 panels (some left to right, some right to left - not sure why not all the same then turn)

  1. Take the six panels which will be used for the roof cone.
  2. Draw a diagonal line, left to right, corner to corner, on three of the panels using the ruler, or another panel, or a piece of string, as a guide.
  3. Draw a diagonal line, right to left, on another three panels.
  4. Put on your gloves, mask and goggles. This protects you from little bits of fiberglass from the panels.
  5. Using the snap-blade craft knife, extended about two inches, cut the panels. Expect to change the blade every panel or so, and change the blade as soon as you feel the knife tearing the material rather than cutting cleanly. (a reciprocating saw in a steady hand works well too-- but a bit messy)
  6. You now have 12 right angle triangles.

Tape some of the edges

(((not sure if this is more conveniently done here or when doing first the walls, then the roof)))

Learn to make hinges

Type 1 hinges: the "easy" ones

  1. This is where the magic of the semi-folding yurt happens. You will make the tape "hinges" that allow your roof and walls to be pre-assembled in accordion-folding halves. This will complete the sealing of the edges of your insulation boards as well. On both the walls and the roof, there is an "easy" hinge to make and a "tricky" hinge to make. Start with the easy hinge on the walls:
  2. Lay two 4x8 wall panels next to each other, tightly butting the 4' sections together. Tape them together while they are flat--this creates what's called the 'inside seam' of the hinge. You can use 3" tape instead of 6" if you like.

Camp-Danger-Folding-Hexayurt-1.jpg

Now stand them up and close the two panels like a book.

Camp-Danger-Folding-Hexayurt-2.jpg

Think of this like bookbinding on the spine of a book: you closed the book at this hinge, so to seal the edges and complete the hinge, use 6" tape along the outside "spine" of the book, that finishes the seal of the raw insulation edges as well.

Camp-Danger-Folding-Hexayurt-3.jpg

Camp-Danger-Folding-Hexayurt-4.jpg

Think of this like bookbinding on the spine of a book: you closed the book at this hinge, so to seal the edges and complete the hinge, use 6" tape along the outside "spine" of the book, that finishes the seal of the raw insulation edges as well.

Type 2 hinges: the "a bit harder" ones

The second hinge or, "tricky hinge" is more difficult but is the "magic" of this style of yurt--it makes it pre-assembled but allows you to fold it up for transport.

Camp-Danger-Folding-Hexayurt-5.jpg

You need a gap between your wall panels that is equal to the thickness of your panel. Most people use 1" insulation, so this gap will be 1". If you use 2" insulation, make it a 2" gap, etc. It's easy to use another panel as a "spacer" to get the right distance.

Camp-Danger-Folding-Hexayurt-6.jpg

Again, start by taping the panels while flat, you could use 3" tape here too. Notice the gap!

Camp-Danger-Folding-Hexayurt-7.jpg

Next, use another panel as a spacer. Then do the "bookbinding" style taping on this hinge as well--you will need 6" tape for this.

Camp-Danger-Folding-Hexayurt-8.jpg

Recall that when the sticky tape touches itself the bond is very strong-- now you have a flexible hinge to make the accordion-folding work for transport. You can try this right now if you have 3 DVD boxes or something similar.

Camp-Danger-Folding-Hexayurt-9.jpg

What makes this work is this newly made flexible hinge, so that you can transport your panels. This technique is far more valuable on the roof cone!

Camp-Danger-Folding-Hexayurt-10.jpg

Walls

Tape some edges for the walls

for the walls, tape some edges (not sure which)

Make 6 hinges for the walls

for the walls, make 6 hinges (not sure which sequence: 1-2-1-2-1-2? or maybe 1-1-2-1-1-2? with numbers meaning types)

Roof

Make roof triangles

for the roof, make the triangles joining two small triangles into a big one x 6 times

Tape some edges for the roof

for the roof, tape some edges (not sure which)

Make roof hinges

for the roof, make 6 hinges (again not sure which sequence)

Assemble the roof cone

This is where the semi-folding yurt becomes amazing. You have done both an easy hinge and a tricky hinge-- you use the same technique for the roof cone. This is awesome because: your raw insulation edges become sealed, your roof cone will be pre-assembled so you don't need to do it piece by piece, AND your roof cone will already have the correct angles at each corner--so that you can plop it onto the top of your walls in an instant and it snaps to shape. You'll see what I mean.

In this photo you see where the "easy" and "tricky" hinges go-- everywhere there's a gap, or on every hypotenuse-joint, is a "tricky" hinge. What is important now is that the tricky hinge changes on the roof cone. Your gap is not equal to the thickness of your panels-- it's 1/2 the thickness. If you forget that, your roof cone will not work and you will be sad. (((doing math: this means that if you use 1" thick insulation panels, your gap for the roof-cone-tricky-hinges will be about 1/2". If you use 2" thick, it'll be 1", etc etc. For my miniature, one half the thickness happens to be a 68th of an inch, but you shouldn't worry about that, just don't forget that it's 1/2 the thickness. On my first hexayurt, a meticulous woodworker measured the insulation and found out it's a little thicker than 1", so our roof-cone-gap became 5/8ths of an inch. You can be meticulous too if you want.)))

Camp-Danger-Folding-Hexayurt-11.jpg

Unlike the wall sections, I don't recommend starting with the "easy hinge," because you end up juggling several panels. Instead, start the roof cone doing "tricky hinges." First, select a spacer that's the right thickness. For my miniature, a cookbook was about 1/2 the thickness of my mini-panels.

Camp-Danger-Folding-Hexayurt-12.jpg

You can use the spacer this way and tape the tricky hinge in halfs as shown. What you need to remember is how the roof cone folds up and opens up: most insulation has logos on one face, and you probably want the logos to be on the inside of your roof so they don't show from the outside. Therefore, the all-silver side will be the side that faces up when you tape this joint. You can use 3" tape here if you like.

Camp-Danger-Folding-Hexayurt-13.jpg

Camp-Danger-Folding-Hexayurt-14.jpg

Camp-Danger-Folding-Hexayurt-15.jpg

Again, this is a "tricky hinge" so use your spacer to help finish the other side of the hinge (the 'bookbinding' part that seals the raw edges of the insulation.) Use 6" tape for this part.

Camp-Danger-Folding-Hexayurt-16.jpg

Camp-Danger-Folding-Hexayurt-17.jpg

You will do the tricky hinge 8 times on your panels. Once that is done, you can add more panels-- but remember that you're making two halfs of the roof cone. Remember this picture and refer to it often:

Camp-Danger-Folding-Hexayurt-18.jpg

When you do the "easy hinge," the "inside seam of the bookbinding" will probably communicate with the "logo side" of your panels (in my example, it's white not grey." Do this seam and the outer "bookbinding" as before. You will be adding these panels on to what you already made-- my picture doesn't look right.

Camp-Danger-Folding-Hexayurt-19.jpg

This is why this design is so fantasic: by the magic of geometry, the gap you created with the tricky hinge creates the perfect angle for your roof-cone. Therefore, when you complete each half of your roof cone, one you open it, it "snaps" to the correct shape for placing on top of the walls--this image doesn't show it perfectly because it's an incomplete half:

Camp-Danger-Folding-Hexayurt-20.jpg

And it accordion-folds into a perfect stack for transport, like the standard hexayurt.

Camp-Danger-Folding-Hexayurt-21.jpg

Camp-Danger-Folding-Hexayurt-22.jpg

I couldn't resist finishing the 1/2 roof cone, this is what it looks like, how it folds up, and how it holds the correct shape of the roof cone. So easy to tape the two halfs together and carry it onto the top of the walls when putting it together. You need 4-5 people for about 5 minutes to lift it, the rest is a two-person job entirely!

view from the inside or logo side, see the gaps for the 'tricky hinges':

Camp-Danger-Folding-Hexayurt-23.jpg

heres the view from outside, hard to tell the hinges are there:

Camp-Danger-Folding-Hexayurt-24.jpg

Folding up:

Camp-Danger-Folding-Hexayurt-25.jpg

Camp-Danger-Folding-Hexayurt-26.jpg

Camp-Danger-Folding-Hexayurt-27.jpg

And here: the roof holds its form, in proper shape. It's actually a little too small in these pictures, but the geometry works out perfectly in larger scale.

Camp-Danger-Folding-Hexayurt-28.jpg

Camp-Danger-Folding-Hexayurt-29.jpg

I added an extra panel to the roof half when I built my model, so it should really look like this:

Camp-Danger-Folding-Hexayurt-30.jpg

Camp-Danger-Folding-Hexayurt-31.jpg

Camp-Danger-Folding-Hexayurt-32.jpg

Camp-Danger-Folding-Hexayurt-33.jpg

Camp-Danger-Folding-Hexayurt-34.jpg

Camp-Danger-Folding-Hexayurt-35.jpg

Fold, travel & unfold

((( bring some of the pictures from above this title)))

(((maybe video)))

Place the roof on top of the walls

elevate the roof and tape it

Fix to the ground

(((link to instructions for this, or copy them here)))

Other things you can add

(((door, windows, air, etc)))

Cookies help us deliver our services. By using our services, you agree to our use of cookies.