Get our free book (in Spanish or English) on rainwater now - To Catch the Rain.

# Basic rainwater collection calculations

This page describes some basic math for calculating the potential collection of a rainwater catchment system.

## Collection Calculations $V=R \times A \times k \times e$

Where:
Symbol Description Units Notes
V Volume of collection gal/time Use this to help determine tank size
R Precipitation inches/time Collect this data or find it at #Precipitation Data
A Footprint of collection surface ft2 This is horizontal projected area of the collection surface. For a rectangular house, use length times width.
e Efficiency of collection surface unitless .75 soil, .8 average, .95 metal 
K Conversion from ft3 to gal 7.48 gal/ft3 You can also combine the 1ft/12in conversion for the precipitation data here.

### US Example

A 1900 square foot house with slanted shingle roof in Columbia, Missouri can collect a potential 2500 gallons in the month of March:

• $V=R \times A \times k \times e$
• $March\ total\ volume = \frac{2.64 in}{mo} \times \frac{1ft}{12in} \times 1900 ft^2 \times \frac{7.48 gal}{ft^3} \times 0.8$
• March total volume = 2500 gallons for the month

### SI Example

A 1000 square meter house with concrete roof in Santo Domingo, Dominican Republic can collect a potential 13,050 liters (3,447 gallons) in the month of July:

• $V=R \times A \times k \times e$
• $July\ total\ volume = \frac{145mm}{mo} \times \frac{1m}{1000mm} \times 100 ft^2 \times \frac{1000liters}{m^3} \times 0.9$
• July total volume = 13,050 liters for the month

Here is a link to a spreadsheet that takes into consideration the size of tank and the use of the water. The spreadsheet accepts as input the precipitation, collection area, efficiency of the roofing material and the use in order to output the collection amounts and warnings if the need outweighs the availability for a month or if the availability is declining over time.

### Online Calculator

A Rainwater Collection Calculator assists in designing a rainwater catchment system. Instructions on how to use the tool as well as the basis for all calculations are presented at Rainwater Collection Calculator.

### Tips

• Keep in mind that this can be calculated per year, month, day, etc. Errors result from low time resolutions because the tank will be filling from rain and emptying from use midcycle. High time resolutions are hard to come by and require more calculations.
• For a quick figure you can use the rule of thumb of .5 gallons per square foot per inch of rain.
• For an even quicker figure you can use SI units with this calculation: The roof efficiency (e.g. .8) in liters for every mm of rain on every m2 of roof. 

### Next Steps

• The spreadsheet could be developed to:
• make best guesses at best tank size
• calculate the buyback time depending on cost of the system and cost of water
• This should have the easier metric example as well
• More links for worldwide precipitation data
• Table of rainwater collection efficiency coefficients for various roofing material.
• A page that builds up the basics with simple drawings.

## Pipe sizing calculations

Too small of pipes will restrict water from flowing through the system fast enough.

Rule of thumb: 1cm2 of gutter cross section per 1m2 of roof area.

Another method would be to use pipe sizing/friction tables to find an acceptable amount of friction.

### Example

Using rule of thumb: for a 23m2 the minimum pipe size is 23 cm2.

1. Converting to diameter from the equation of Area=Pi*(Diameter/2)2, yields:
• Solving for diameter, yields Diameter=2*squareroot(Area/Pi)
• 2*Squareroot(23 cm2/pi) = 5.41 cm
2. Converting to inches, yields:
• 5.41cm * 1in / 2.54cm = 2.13 in

Therefore a pipe diameter of at least 2.13 inches should be used. The most common size that meets that requirement is 2.5 inch.

## First Flush Calculations

Because of contamination on the roof the first volume of rain should be diverted from the storage tank. As a rule-of-thumb, contamination is halved for each mm of rainfall flushed away .

Calculation: meters squared (roof area) X pollution factor = liters to be diverted.

or Time based rule-of-thumb: Divert the first 10 minutes of rain.

Downpour rain per minute * 10 minutes = volume to divert

or

Area based rule-of-thumb: 0,41 liters for every meter squared of roof[verification needed] OR 10 gals for ever 1,000 foot squared of roof