Get our free book (in Spanish or English) on rainwater now - To Catch the Rain.

Difference between revisions of "3D Printable Goniometer"

From Appropedia
Jump to navigation Jump to search
Line 73: Line 73:
 
== Benefited Internet Communities ==
 
== Benefited Internet Communities ==
 
* Name and add links to at least 5 using single brackets around [url name]
 
* Name and add links to at least 5 using single brackets around [url name]
 +
* Medecins sans Frontieres [https://www.msf.fr/ msf.fr]
 +
* [https://www.online.physio/ Online Physio]
 +
*
  
 
==References==
 
==References==

Revision as of 05:15, 6 December 2019

MOST Delta filament as guide.JPG This page was part of an MTU course MSE4777 OA and MSE4777 OB/MSE5777/EE4777/EE5777: Open-source 3-D printing

Please leave comments using the discussion tab. The course runs in the Fall semester. It is not open edit.


3D Printable Goniometer

Project developed by Eric Houck, Houcke
Status
This OSAT has been designed but not yet tested - use at own risk.
This OSAT has been prototyped.

You can help Appropedia by contributing to the next step in this OSAT's status.

Abstract

Goniometers are simple devices used to measure the angular range of motion of human limbs. It is common for doctors to monitor the muscular recovery and rehabilitation of a patient using a goniometer. They are not expensive, however they are flimsy and break easily. A 3D printed goniometer can be more durable than a commercial one. Additionally, one may not always have a goniometer handy. Being a relatively simple device, a goniometer prints very quickly and cheaply. Typically, a doctor will use a goniometer to measure the range of motion of a patient. However, with the 3D printed version being so extremely cheap, patients can be provided their own goniometers to monitor their own range of motion, thus reducing expensive doctor's visits.

Goniometer3Dprint.jpg

Bill of Materials

Provide a full BOM -- Materials needed for fabrication of device and alternative materials if they are not available, prices/sources of non-printable parts

  1. Printed parts on Thingiverse https://www.thingiverse.com/thing:4022729 (Cost: 16 cents total filament use)
  2. Pencil (Cost: <$1.00 to purchase, however they are very common and can be borrowed at no cost)
  3. Small piece of paper (Cost: Take from recycling/garbage. This should be found for free with no issues)

Tools Needed

  1. MOST Delta RepRap or similar RepRap 3-D printer
  2. Paper
  3. Pencil
  4. Straightedge
  5. Protractor
  6. Scissors
  7. Glue Stick

Skills and Knowledge Necessary

  • Minor scissor skills to make the paper slip with the angle measurements

Technical Specifications and Assembly Instructions

  • Provide directions for print/assembly - be detailed enough in your “how to” to ensure that someone could construct the device from your description. Consider the elegance of IKEA like instructions.
  • Include print time estimate
  • Include assembly time estimate
  • Including drawings or pictures of the device at stage of assembly at minimum. (http://www.appropedia.org/Special:Upload)

1. Print Parts

  • Using your 3D printer, print out the attached thingiverse files
  • Print 1x gen_base_01.stl, 1x geniometer_spinner_01.stl, 2x goniometer_extend.stl
  • Total print time estimate: 40min
 Print Settings:
 Resolution: 0.3 mm
 Temperature: 205 C
 Material: PLA
 Print speed: 20mm/s edges, 40 mm/s infill
 Infill: 20%
 Retraction: ON, Z-hop: ON, Skirt: ON

2. Paper Slip

Gon base graphic.jpg
Gon spin graphic.jpg
  • Using the scissors, cut the small piece of paper to fit inside the rounded portion of the printed part (gen_base_01.stl). This will serve as the angular scale for the goniometer. The paper should fit in the region outlined in red.
  • With the protractor, transfer the angle measurements from the protractor in increments on 10 degrees onto the rounded slip of paper cut in step 2. Ensure that the measurements of 0 & 180 degrees line up with the center pivot point of the part.
  • Using the glue stick, attach the paper to the radial spokes protruding from the center pivot. The paper should sit below the outer rim of the rounded section.

3. Snap Together

  • Snap the printed parts (gen_base_01.stl) and (geniometer_spinner_01.stl) together through the centers of the rounded portions (outlined in green). They should be aligned so that when the handles are pointing in opposite directions, their long straight edges align.
  • To make the goniometer longer, take the printed parts (goniometer_extend.stl) and fit their diamond shaped extrusions into the ovular openings on the handles of (gen_base_01.stl) and (geniometer_spinner_01.stl).

Common Problems and Solutions

  • The male end of the circular snap fitting can turn out poorly if the print speed is too high. I used a maximum of 40 mm/s

Cost savings

  • Total print cost of OSAT Goniometer, $0.16
  • Paper/Pencil/Glue costs: Negligible
  • Commercial equivalent: $4.19 Goniometer at Allegro Medical
  • Total Savings: $4.03
  • Relative Savings: 96.2%

Benefited Internet Communities

  • Name and add links to at least 5 using single brackets around [url name]
  • Medecins sans Frontieres msf.fr
  • Online Physio

References