No edit summary |
No edit summary |
||
| Line 43: | Line 43: | ||
</ref> | </ref> | ||
="Reprinting the Telegraph:Replicating the Vail Register Using Multi-materials 3D Printing"= | |||
*Used SFF to fabricate a complete, active electromechanical system (telegraph) | |||
*produced a complete electromagnet:stacked layers of 20 turns each, total resistance of 11.4Ω | |||
<ref>Alonso, Matthew P., Evan Malon | |||
e, Francios C. Moon, and Hod Lipson. "Reprinting the Telegraph:Replicating the Vail Register Using Multi-materials 3D Printing." Cornell.edu. Web. 30 May 2012. <http://creativemachines.cornell.edu/sites/default/files/SFF09_Alonso.pdf>. | |||
</ref> | |||
="SpoolHead(RepRap Wiki)"= | |||
*Reprap toolhead for printing with metal wire | |||
*Made to print with nichrome wire to replicate RepRap electrical components | |||
<ref>"SpoolHead." - RepRapWiki. Web. 30 May 2012. <http://reprap.org/wiki/SpoolHead>. | |||
</ref> | |||
="Materials Science(RepRap Wiki)"= | |||
*ConductiveMaterials can serve as CircuitBoard traces, wiring, antennae, electro magnets, and faraday cages, along with actual electrical components such as capacitors, resistors, and inductors | |||
*Work done with printing metals and conductive filler | |||
<ref>"MaterialsScience." - RepRapWiki. Web. 30 May 2012. <http://reprap.org/wiki/MaterialsScience>. | |||
</ref> | |||
=References= | =References= | ||
<references/> | <references/> | ||
Revision as of 16:19, 30 May 2012
Introduction
This page comprises a literature review of 3D printing with electrically conductive materials. Information is taken straight from sources, as credited.
Search Phrases
- Conductive 3D printing
- Conductive 3D printing polymers
- Conductive additive layer manufacturing
"Rapid prototyping of electrically conductive components using 3Dprinting technology"
- made of plaster-based powder bound layer-by-layer by an inkjet printing of a liquid binder
- impregnated by a dispersion of carbon nanofibers (CNF) in epoxy resin
- Surface resistivity of the model below 800 Ω/sq has been obtained when impregnated by a mixture containing less than 4 wt.% CNF. Volume resistivity of the molded and hardened CNF dispersion used for model impregnation have also been measured and a value less than 200 Ω cm has been obtained at 3 wt.% CNF content
- carbon-black or metal powders increases the viscosity of the infiltrant so that it is not able to impregnate the 3D model structure
- the average diameter of the fibers is 100 nm and typical length is 50–200 μm
"Inkjet Printing of Narrow Conductive Tracks on Untreated Polymeric Substrates"
- Small conductive tracks are created by direct inkjet-printing
- Ink with 30 nm silver particles onto flexible and transparent untreated polyarylate foils
- Diameter as narrow as 40 micrometers
- Conductivity is 13 to 23 % that of bulk silver
- may be applied in plastic electronics
"Gravure printing of conductive particulate polymer inks on flexible substrates"
- conductive lines on paper and plastic films
- inks contained metal particles in an organic medium and were cured in temperatures of 70–120 °C
- A printed resistance down to ∼50 mΩ/□ was obtained, with conductor lines 4–7 μm thick
- thick ink layer is needed for high conductivity
- printed antennas and inductors
"Reprinting the Telegraph:Replicating the Vail Register Using Multi-materials 3D Printing"
- Used SFF to fabricate a complete, active electromechanical system (telegraph)
- produced a complete electromagnet:stacked layers of 20 turns each, total resistance of 11.4Ω
"SpoolHead(RepRap Wiki)"
- Reprap toolhead for printing with metal wire
- Made to print with nichrome wire to replicate RepRap electrical components
"Materials Science(RepRap Wiki)"
- ConductiveMaterials can serve as CircuitBoard traces, wiring, antennae, electro magnets, and faraday cages, along with actual electrical components such as capacitors, resistors, and inductors
- Work done with printing metals and conductive filler
References
- ↑ J. Czyżewski, P. Burzyński, K. Gaweł, J. Meisner, Rapid prototyping of electrically conductive components using 3D printing technology, Journal of Materials Processing Technology, Volume 209, Issues 12–13, 1 July 2009, Pages 5281-5285, ISSN 0924-0136, 10.1016/j.jmatprotec.2009.03.015. (http://www.sciencedirect.com/science/article/pii/S092401360900106X)
- ↑ van Osch, T. H. J., Perelaer, J., de Laat, A. W. M. and Schubert, U. S. (2008), Inkjet Printing of Narrow Conductive Tracks on Untreated Polymeric Substrates. Adv. Mater., 20: 343–345. doi: 10.1002/adma.200701876
- ↑ Marko Pudas, Niina Halonen, Päivi Granat, Jouko Vähäkangas, Gravure printing of conductive particulate polymer inks on flexible substrates, Progress in Organic Coatings, Volume 54, Issue 4, 1 December 2005, Pages 310-316, ISSN 0300-9440, 10.1016/j.porgcoat.2005.07.008. (http://www.sciencedirect.com/science/article/pii/S0300944005001700)
- ↑ Alonso, Matthew P., Evan Malon e, Francios C. Moon, and Hod Lipson. "Reprinting the Telegraph:Replicating the Vail Register Using Multi-materials 3D Printing." Cornell.edu. Web. 30 May 2012. <http://creativemachines.cornell.edu/sites/default/files/SFF09_Alonso.pdf>.
- ↑ "SpoolHead." - RepRapWiki. Web. 30 May 2012. <http://reprap.org/wiki/SpoolHead>.
- ↑ "MaterialsScience." - RepRapWiki. Web. 30 May 2012. <http://reprap.org/wiki/MaterialsScience>.