No edit summary
No edit summary
Line 1: Line 1:
{{777}}
{{777}}
<!--infobox-->
{{OpenKhowHowManifest
|manifest-date-created=
|manifest-date-updated=2020-06-04
|manifest-author-name=Kathy Nativi
|manifest-author-affiliation=Appropedia
|manifest-autho-email=info@appropedia.org
|title=3-D Printable Speaker Demo
|description=This page contains the instructions and files necessary to 3D-print a loudspeaker.
|intended-use=development, industry
|keywords=
|project-link=
|contact-affiliation=MOST
|contact-appropedia-user=User:Brhubbar
|image=3-D_Printed_Speaker_Enclosure.JPG
|development-stage=
|made=No
|made-independently=No
|derivative-of=
|manufacturing-files=https://www.myminifactory.com/object/3d-print-3-d-printable-speaker-107278
|manifest-language=eng
|date-published=
|main-materials=Plastic
|estimated-cost-amount=  1.25
|estimated-cost-currencyUSD
|sustainable-development-goal=Sustainable Development Goal 8, Sustainable Development Goal 12
|documentation-language=eng
}}
<!--end infobox-->
== 3-D Printable Speaker Demo ==
== 3-D Printable Speaker Demo ==
Project developed by [[User:Brhubbar|Ben Hubbard]]
Project developed by [[User:Brhubbar|Ben Hubbard]]

Revision as of 20:36, 5 June 2020

3-D Printable Speaker Demo

Project developed by Ben Hubbard

Abstract

This page contains the instructions and files necessary to 3D-print a loudspeaker. This isn't the best sounding speaker on the planet - it could definitely use some tuning, a better suspension, and a real enclosure, but it serves as a very low-cost (~$1.25) solution for producing audio. The original intention of this design is as an educational aide - a speaker is one of the most effective ways to illustrate the interactions between electricity and magnetism. A lesson plan will be included at a later date to guide this education.

Demo of the speaker playing Chin Up by Puppet
Error in widget YouTube: Unable to load template 'wiki:YouTube'

Bill of Materials

  1. 3D Printed Components (files here)
    • Enclosure - Holds the suspension and the magnet.
    • Voice coil - Moving part of the speaker, produces sound
  2. 2-3 12mmx3mm N52 disc magnets (top/bottom polarized). These are available for $10 on Amazon, with enough magnets for many speakers, or other projects. (the three magnets for this project thus total to $0.75) - Forms part of the motor structure
  3. 12-14 feet (around 4 meters) 28 AWG enameled copper wire (often marketed as inductor wire). This is available in 500 ft rolls on Amazon for $7. The wire used by a single speaker costs around $0.20 - Used to create the voice coil

Tools Needed for Assembly

  1. MOST Delta RepRap or similar RepRap 3-D printer
  2. Wire cutters/Diagonal cutters
  3. Super glue or another quick-setting adhesive to prevent the voice coil from unwinding or buzzing
  4. Knife or Lighter to strip enamel from wire ends
  5. Audio amplifier to power the speakers. Aim for one that accepts bare wire. A low cost option from the US is Lepai. A Chinese company called Lepy sells cheaper copycats of Lepai amps on Amazon for around $25.
  6. A multimeter, if you would like to check the impedance of your speaker. For the amount of wire and diameter of the coil specified, it should be around 2 ohms DC Resistance.


Skills and Knowledge Necessary

  • None

Technical Specifications and Assembly Instructions

3D Printing

~40 minute print time for a single speaker

  1. High quality in the print is not required here. This will take around 20g total of filament, costing around $0.40
  2. The cone is at a 40 degree angle and requires support material. I used a 10% zigzag support. Support is not necessary anywhere except under the cone.
    • Unless you're going for an aesthetic, removing the support is not critical for the sound quality. Future redesign would potentially switch up the cone design - it's unclear how much this helps or hurts the frequency response of the speaker.

3-D Printed Speaker Enclosure.JPG 3-D Printed Voice Coil.JPG

Mechanical Assembly

10 - 15 minutes, depending on adhesive set time

  1. Clean of the prints. They should look like those pictured above
  2. Use an adhesive to glue a single magnet into the standoff in the enclosure. It will probably sit flush, but it's not a problem if it sits a little high. Add one or two magnets on top of that. This standoff positions the magnets right on the end of where the voice coil will sit. This is ideal for maximizing the magnetic interaction between the voice coil and the magnet (determined empirically)
    3-D Printed Speaker Enclosure.JPG
  3. Place the voice coil on a flat surface, cone facing upward. Tape one end of the 28 AWG enameled wire onto the flat of the speaker, leaving around 8 inches (20 cm) of slack.
    3-D Printed Voice Coil Wrapping.JPG
  4. Wrap 12-14 feet of wire around the upright cylinder of the voice coil, keeping the wire tight around the coil and kink-free. This will make a 2 ohm speaker. These are more sensitive and lighter, but most amps are designed for 4 or 8 ohm speakers. This can be resolved by building two speakers, wired in series, or by doubling the amount of wire in the wrap. I recommend 2 speakers. (My theory is that you'll have lighter speakers and make better use of your magnets, but I haven't done the math on it.)
    • At this point, if you want to check the DC resistance of the coil, strip both ends of the wire (without cutting it) and measure the resistance. Wrap further if desired.
  5. Leave another 8 inches (20 cm) of slack, then cut the wire. Tape this end down as well, keeping the coil wrapped tight.
    3-D Printed Voice Coil Wrapped.JPG
  6. Coat the entire voice coil in super glue. Any un-coated wires will vibrate during use and make your speaker sound particularly rough (static-y).
  7. At this point, you can strip the wire ends with a knife. I've heard a lighter will also work for this.
  8. Connect the speaker to an amplifier and test it, either holding the voice coil by the suspension or holding it in the enclosure.
  9. If it sounds okay, glue each of the suspension pieces into the notches on the enclosure. Allow the glue to set completely before running the speaker again.
    3-D Printable Speaker.JPG

Use

  1. Connect the speaker to an amplifier, and play music, or do a demo to get kids excited about speakers! (lesson plan to come)
    • Most amps want 4 or 8 ohm speakers. If you built according to these directions (and didn't double the amount of wire), you have a 2 ohm speaker. I recommend you build a second speaker and wire them in series.
  2. When using multiple speakers, polarity is important (messed up polarity will make your speakers very quiet, particularly on the high frequency side of things). You'll notice that polarity wasn't a detail of interest during construction. Simply grab a battery (I used a AA), and press one lead against the negative end of the battery, and the other end against the positive lead of the battery.
    • If the speaker moves up, mark the wire contacting the positive lead of the battery with red tape.
    • If the speaker moves down, mark the wire contacting the negative lead of the battery with red tape.
    • Repeat this for each speaker. The leads marked with red tape are your positive leads. When connecting in series, connect a positive lead to the positive terminal on the amplifier, the negative lead to the positive lead of the next speaker, then the negative lead of that speaker back to the negative terminal on the amplifier, making a big loop.
  3. I recommend turning the bass way down - these things are sensitive to low frequencies. Set them on a table or inlay them into a larger baffle to get a better bass effect, thanks to half space acoustics

Common Problems and Solutions

  • Be sure your wiring is correct. Connect positive leads to the positive terminal of the amp, and negative leads to the negative terminal of the amp.
  • If you're not getting audio out of your amp, test it with a known functioning speaker. It's pretty difficult to build these and not have any sound produced.
    • Check that the enamel is completely stripped off. I twist my stripped leads together end-to-end with 16 AWG stranded wire before connecting to the amp. This gives better odds that everything will make electrical contact.
  • There are many sources for buzzing in these speakers. Be sure that the voice coil is well glued down, as well as the suspension and the magnet in the middle. Other buzzing may come from resonance in the suspension (its not very well damped) and misalignment of the voice coil with the standoff holding the magnet. This may require tolerance adjustments and new prints.
  • Be sure to turn the

Cost savings

  • The cost of this comes in around $1.25 per speaker, depending on where parts are sourced. It's easy to use these for educational demos or even computer speakers if you're living on a budget. Comparable (admittedly better sounding, but less useful for educational purposes) speakers typically go for around $20, making these about 5% of the cost.
Cookies help us deliver our services. By using our services, you agree to our use of cookies.