Create the page "Tensile strength" on this wiki! See also the search results found.
- Effects of PLA Color on Material Properties of 3-D Printed Components Tensile Strength of Commercial Polymer Materials for Fused Filament Fabrication 3-D4 KB (489 words) - 15:55, 23 February 2024
- printers using proprietary FDM in terms of tensile strength with the same polymers. However, tensile strengths of the large sample set of RepRap prints fluctuated5 KB (517 words) - 15:55, 23 February 2024
- 3-D printer for a wide range of materials. The samples are tested for tensile strength following ASTM D638. The results are presented and conclusions are5 KB (553 words) - 15:59, 23 February 2024
- biocomposite aims for suitable mechanical properties in terms of tensile and compressive strength. It is composed of acrylic acid, cellulose acetate, α-cellulose5 KB (498 words) - 16:04, 23 February 2024
- addition of stamp sand reduced the material's ultimate tensile strength by about half compared to the strength of raw recycled ASA, regardless of the percent stamp4 KB (1,014 words) - 16:05, 23 February 2024
- functional as commercial 3-D printers Using tensile specimen here:http://www.thingiverse.com/thing:28987 Tensile Strength of Commercial Polymer Materials for Fused7 KB (796 words) - 16:03, 23 February 2024
- effective and will be more environmentally sound while still having high tensile strength. This project is taking place from May 25th to July 5th and will take6 KB (646 words) - 13:04, 9 June 2023
- filament printing and the bulk virgin material. The results showed the tensile strength of parts manufactured from the recycled PC particles (64.9 MPa) were4 KB (911 words) - 14:44, 28 February 2024
- Recycled 3-D Printing Filament Open source rapid prototyping of OSAT Tensile Strength of Commercial Polymer Materials for Fused Filament Fabrication 3-D3 KB (381 words) - 15:30, 23 February 2024
- quantify ultimate tensile strength (UTS). And yield strength using ASTM D638-14 horizontally-oriented Type I and IV geometries. Tensile strengths of 61.6 and5 KB (612 words) - 16:03, 23 February 2024
- performance was measured by the disc-shaped compact tension (DCT) test. The tensile strength ratio (TSR) was used to determine the moisture susceptibility and the4 KB (1,067 words) - 16:04, 23 February 2024
- decrease in tensile modulus, flexural modulus and lower yield pt shifted toward the lower strain, no changes in tensile and flexural strength, over 40% recycled22 KB (2,574 words) - 13:18, 14 April 2023
- proved to be very efficient when under compressive stress, but their tensile strength was rather disappointing. Although more tests should be made, we can28 KB (2,866 words) - 12:10, 28 February 2024
- Composites have good tensile strength and resistance to compression, making them suitable for use in aircraft part manufacture. The tensile strength of the material15 KB (2,123 words) - 16:47, 29 January 2024
- RepRap Mechanical Testing Literature Review (section Measurement of anisotropic compressive strength of rapid prototyping parts)NOTE: This is for compressive strength, not tensile strength where increase in raster angle should reduce tensile strength. Chacón, J. M., et al, "Additive33 KB (4,602 words) - 13:24, 14 April 2023
- of 3 parts clay to 5 parts sand, adding as much straw as needed for tensile strength. Once you have the ratio go ahead and evenly spread out your sand onto11 KB (1,873 words) - 16:16, 29 January 2024
- harvesting. In this regard, a low-cost reliable method to test the tensile strength of rope is needed to validate alternative materials for use in harvesting3 KB (268 words) - 12:06, 28 February 2024
- Carbon fiber composites are valued for their high Young's modulusW and tensile strength as well as their light weight. Some forms of carbon fiber are also17 KB (2,187 words) - 22:02, 29 February 2024
- with Open-Source 3-D Printers Under Realistic Environmental Conditions Tensile Strength of Commercial Polymer Materials for Fused Filament Fabrication 3-D5 KB (540 words) - 16:05, 23 February 2024
- the tensile strength and Young's modulus of the product produced. Graph 1 and Graph 2 show how the relative tensile strength and relative tensile modulus23 KB (3,164 words) - 00:04, 8 March 2024