Create the page "Nuts" on this wiki! See also the search results found.
- vertices, 14 M8 nuts, 14 M8 washers and 3 370mm M8 threaded rod. Using the 290mm long jig, space each vertex from its neighbors and tighten the nuts so that a26 KB (4,116 words) - 14:03, 6 June 2022
- Las Malvinas rainwater catchment system 2014 (category Nuts)PVC adapter [4] 1 60.00 60.00 Botellon PVC adapter [6] 1 80.00 80.00 Bag of nuts [25 mm.] 1 92.00 92.00 Bag of bolts [40mm.] 1 67.00 67.00 Outdoor L-brackets7 KB (726 words) - 11:51, 28 February 2024
- Food crops (section Seeds and nuts)meat in many dishes. The variety of seeds and nuts available as food crops is enormous. Both seeds and nuts are botanically the same because they consist6 KB (835 words) - 17:28, 23 October 2023
- four M3 nuts secure the two holding pieces to the idler end of the pump. Put two nuts it the top of the holder closer to the carriage and two nuts in the22 KB (2,291 words) - 12:01, 28 February 2024
- break, sometimes surprisingly easily. It's better to use nylon locking nuts or jam nuts if there is concern about backing out. Resist the urge to manually6 KB (960 words) - 15:50, 9 June 2023
- washer. Start nuts on the M3 x 50mm screws and tighten. Mounting vertical boards. Vertical board secured with washers and nuts on idler end, nuts only motor8 KB (990 words) - 23:18, 7 July 2022
- FBP Nutsy (category Nuts)the user to see the shelled nuts and to view when the sheller is full. The lid includes a small, hinged door that allows nuts to be added without removing10 KB (1,541 words) - 19:24, 29 January 2024
- too many nuts are unshelled, raise rotor. If you have nuts with a wide variety of sizes you may have to adjust machine to shell the larger nuts first. Then4 KB (657 words) - 15:18, 23 February 2024
- the vertices such that the flats near the nuts tightly hold the jig between adjacent vertices and tighten the nuts. Repeat with all sides of the triangle4 KB (458 words) - 19:08, 29 May 2023
- version - compliments of Marcin at Open Source Ecology - removed all the nuts and bolts and screws Please note that all the instructions are in the HardwareX7 KB (1,328 words) - 21:43, 16 April 2024
- proper orientation. Secure holder with nylock nuts. Secure the tool holder with M3 nylock nuts. Tighten the nuts until just touching the tool holder - do not24 KB (3,220 words) - 19:07, 16 April 2024
- as shown with the platform sandwiched between two washers and nuts. Do not tighten the nuts. Right corner piece with carbon fiber rod. Push one end of the8 KB (1,080 words) - 19:09, 29 May 2023
- bottom front threaded rod. Don't tighten the nuts yet. . Attach it to the top rod. Don't tighten the nuts. Don't use the zip-ties yet. . The frame should5 KB (649 words) - 19:09, 29 May 2023
- approximately 500 nuts per load (the kukum drier) to 20,000 nuts per load (the Cochin drier). It is reported that the Chula copra drier (5,000 nuts/load/24 hours)43 KB (5,343 words) - 13:16, 7 December 2023
- sheller are rough. Rough surfaces will shell the nuts correctly. If the surface is too smooth, the nuts will slide and not be shelled. Rough working surfaces3 KB (614 words) - 12:35, 23 February 2024
- Set the top nuts of the lead screws to approximately halfway of the lead screw, then push the X axis into the spring to thread the bottom nuts up. Thread5 KB (546 words) - 19:09, 29 May 2023
- Squeezing nut into bar clamp. Put M3 nuts in the nut pockets in each of the six bar clamps. With pliers, squeeze the nuts all the way into the clamp until5 KB (836 words) - 19:09, 21 July 2022
- Gear Driven Gear located on axle assembly. Attached to wheel via 3mm hex nuts and bolts, compressed together within axle assembly. 4 Wheel Wheel located5 KB (46 words) - 17:55, 2 March 2022
- from Full Belly Project. Diagram of the LC Sheller: Unshelled nuts in the top, shelled nuts out the bottom. While improvements were made to the UNS, additional4 KB (491 words) - 18:20, 29 January 2024
- the tie rods. A completed pulley consists of a printed pulley with two M3 nuts and two M3 x 8mm set screws. Pulleys must be secured to the motors before5 KB (729 words) - 06:27, 30 May 2023