MOST HSPrusa frame 0.jpg

Printed Parts[edit | edit source]

Description Count Image
Footed bottom vertex 4 MOST HSPrusa frame vertex foot.gif
Top vertex 2 MOST HSPrusa frame vertex top.gif
Rod clamp (some shown white in the pictures below, but all should be silver) 6 MOST HSPrusa frame bar clamp.gif

Vitamins[edit | edit source]

Description Count
440 mm M8 threaded rod (Top horizontals and bottom of z-axis) 3
370 mm M8 threaded rod (Triangle sides) 6
290 mm M8 threaded rod (Lower horizontals) 4
608zz bearings 4
M8 nut 60
M8 washer 66
M3×12 mm cap screw (Melzi mount) 4
M3 nut 4
M3 washer 4

Pointers[edit | edit source]

  • Threaded rod should pass through the holes in the printed frame pieces relatively easily; ream the holes well. The threaded rod can be used like a file to open up the holes a bit more.
  • Some of the M8 nuts must be threaded deeply onto threaded rod, which can take time. There are a few ways to speed it up, one of which is to start the nut and then roll the nut across your hand by moving the threaded rod with the other hand. If a package of M8 nuts, washers and/or bearings must be advanced along the rod, it can be done semi-simultaneously using a similar method.

Assembly - Summary[edit | edit source]

  1. Prepare printed parts
  2. Assemble triangles
  3. Assemble horizontal rods
  4. Put them together

Assembly - Step-by-Step[edit | edit source]

  1. With an 8mm drill bit and a piece of threaded rod, thoroughly ream out all of the 8mm holes in the apexes, using the threaded rod as a file. These parts are quite durable and they are unlikely to break; be aggressive. The threaded rod should pass through the holes relatively easily.
  2. Parts for one triangle.
    Put a rod clamp on one 370 mm rod with a washer and a nut on both sides. Don't screw it tight; you'll need to adjust the position later. Put a nut and a washer on each side of each rod.
  3. Complete triangle.
    Put the triangle together. Make sure the clamp goes between the footed vertices and the feet are both on one edge of the triangle.
  4. Repeat for the other triangle.
  5. With the 290mm wooden jig, space the vertices such that the flats near the nuts tightly hold the jig between adjacent vertices and tighten the nuts. Repeat with all sides of the triangle on both triangles.
  6. Top base rods.
    Assemble the two top horizontal rods for the base (290 mm), which will go through the top holes of the footed vertices. The image shows the pieces for one rod, and another rod assembled.
  7. Top rods.
    Assemble the horizontal rods for the top of the frame(440 mm).
  8. Bottom base rods.
    Assemble the bottom horizontal rods for the base (290 mm).
  9. Attach the horizontal rods to between the triangles. The bottom frame rod with the nuts and washers on it is the front of the machine. The extruder will be on the left of the top rods, so leave more space there than on the right. The top horizontal rods on the base have one nut on one side, and two nuts on the other. The side with one nut goes to the right.
  10. With the 234mm wooden jig, space the horizontal bars equally between vertices tightening only the nuts on horizontal rods at the base. The top horizontal rods will be spaced and tightened later.

MOST Printer Frame Measurements 2.jpg

Return to Overview[edit | edit source]

Back to overview

FA info icon.svg Angle down icon.svg Page data
Authors Bas Wijnen, Jerry Anzalone
License CC-BY-SA-3.0
Language English (en)
Related 0 subpages, 14 pages link here
Aliases HS RepRap frame, MOST RepRap frame
Impact 398 page views
Created May 6, 2013 by Bas Wijnen
Modified May 29, 2023 by Felipe Schenone
Cookies help us deliver our services. By using our services, you agree to our use of cookies.