|Part of||Practical Action Technical Briefs|
|License||CC BY-SA 4.0|
|Translate to||Français, Español, Kiswahili, 中文, العربية, Русский, more|
|Export to||PDF, LaTeX, EPUB, ODT|
|Cite as Oorxax (2021). "Fruit leathers (Practical Action Brief)". Appropedia. Retrieved 2021-10-28.|
Fruit leathers are made by drying a very thin layer of fruit puree to produce a product with a texture similar to soft leather. Fruit leathers are eaten as a snack and are often targeted at health food markets, using marketing images such as "pure", "sun dried" and "rich in vitamins". Such claims are not unreasonable given that low temperature drying is a gentle process that results in less loss of nutrients than, for example, canning in which up to 65% of minor nutrients can be destroyed. Losses of vitamin A and C are, however high, if the fruit is dried in direct sunlight. Fruit leathers can be made from one type of fruit or blends of different fruits. They may be sweetened, by adding sugar or flavoured with chopped nuts, coconut or spices.
The preservation of fruit leathers depends on their low moisture content, typically 15 to 25%, the natural acidity of the fruit used and high sugar contents. The products have a shelf life of up to 9 months provided they have been sufficiently dried and properly packaged.
Production of fruit leathers[edit | edit source]
This technical brief describes the production of fruit leathers at three scales; from a very small simple home based system, through cottage industry to small industrial production. The following basic steps are involved at all levels of production:
- selection and preparation of the fruit including intermediate preservation to allow production to continue out of season.
- preparation of the puree
- batch preparation
- packing and storage.
Selection, preparation and intermediate storage[edit | edit source]
A high quality product can only be made from good quality raw materials and production should not, as too often happens, be based on second grade fruit that is not suitable for the fresh market. Fruit that has been rejected for being too large, too small or because of surface blemishes is, however, usually acceptable.
Fully ripe soft fruits are very susceptible to bruising when handled and bruised areas will quickly begin to rot. It is thus better to purchase semi-ripe fruit (which is usually cheaper) and allow it to fully ripen in the processing area. This also has the advantage of allowing the daily selection of fruits of equal ripeness.
Incoming fruit should be selected and any unsuitable material removed from the processing area and properly disposed of; not simply put in an open bin outside. Selected fruits are then washed in chlorinated water (one teaspoon of bleach per gallon of water) and then peeled, de-stoned etc, depending on the type being used. Only stainless steel knives should be used as mild steel will corrode and stain the flesh. Some fruits require special attention. Banana has a very low level of acidity and is also subject to what is known as enzymatic browning which results in rapid discoloration after peeling and cutting. After peeling, bananas should be quickly immersed in a water containing a small quantity of a chemical, sodium metabisulphite, which controls such browning. The solution should have a concentration of 400 parts per million of sulphur dioxide.
Use of Sulphur dioxide (SO2)[edit | edit source]
SO2 has been widely used in fruit and vegetable products to control enzymatic colour changes such as the darkening of a freshly cut apple or potato. It also acts as a preservative, controlling the growth of moulds and yeasts. SO2 is produced by either burning a small piece of sulphur or by dissolving sodium metabisulphite in water. The second method is more controllable.
The levels of SO2 used are measured in parts per million or ppm. Concentrations of 400 to 1000ppm are used for dips to control colour changes and retard the growth of moulds and yeasts. A 400ppm bath, for example, is made by dissolving 6g of sodium metabisulphite in 10 litres of water.
NB SO2 gas is harmful if breathed in, it should only be used in a well ventilated room
In recent years, the use of SO2 has been increasingly controlled and it has been banned in many foods in the USA. Similar changes to food laws are is likely in Europe. In such situations browning can be controlled by the addition of citric acid but this is far less efficient than sulphur dioxide.
The most convenient production plan for very small producers is to use fruits that are in season at any given time. This does, however, have disadvantages that include:
- one particular flavour of fruit leather may be much more popular than others
- it will only be possible to produce small quantities of product in a short season
- It is, however, possible to produce all year by preserving prepared fruit (or fruit puree) in sealed drums with added SO2 at a level of 600ppm. Fruit may be stored for many months in this way. Intermediate preservation also allows fruits to be purchased at the peak of the harvest when prices are at their lowest. While most of the SO2 absorbed during intermediate preservation will be lost during drying it is recommended that purees made from preserved fruits should be briefly boiled prior to drying to reduce the level of residual SO2
Preparation of puree[edit | edit source]
At the simplest level fruit may be pulped to a puree by hand using a food mill, or Mouli Legume as shown in figure 1, in which the food is pushed through a mesh by a rotating paddle. If electric power is available a food liquidiser, followed by sieving will greatly increase production outputs. At larger scale, powered high-speed blender wands are recommended.
Drying[edit | edit source]
It is recommended that fruit leathers are not dried in direct sunlight as there will be considerable loss of colour and vitamins A and C. Indirect dryers, either solar or mechanical suitable for drying these products are described in Practical Action's Technical Brief - Small Scale Food Dryers.
After about a day or so, in a solar dryer, or 5 hrs, in an artificial dryer, it will be found possible to lift the leather sheet away from the tray. At this stage the product should be turned over and dried on the other side. Prior to packing fruit leathers are frequently lightly dusted with starch to reduce their stickiness.
Packaging[edit | edit source]
Fruit leather is normally sold in the form of a roll interleaved with greaseproof paper to avoid it sticking together. Strips, of the required weight, are laid on a piece of greaseproof paper and simply rolled with the paper. The final product should then be packed in polythene or polypropylene heat-sealed bags. The latter, if available, are to be preferred as they provide greater protection against moisture. The bags should then be placed into outer boxes to protect them from light. The product should be clearly labelled stating, as a minimum, the name of the product, net weight, ingredients list and the name and address of the manufacturer. Where available, self-adhesive labels are recommended.
Equipment required[edit | edit source]
Scales, balance to weigh in grams, plastic containers to wash fruit, stainless steel knives, spoons, chopping boards, double boiling pan, fruit pulper, large sealable food grade bins for intermediate storage of pulps, dryer, heat sealer
Further reading[edit | edit source]
- Fruit Juice Processing (Practical Action Technical Brief)
- Fruit Waste Utilisation Practical Action Technical Brief
- Mixed Fruit Juice Practical Action Technical Brief
Useful addresses and contacts[edit | edit source]
Fisher Scientific UK Ltd. (Heat sealing equipment producers)
Bishop Meadow Road
Tel: +44 (0) 1509 231166
Fax: +44 (0) 1509 231893
Practical Action The Schumacher Centre for Technology and Development Bourton-on-Dunsmore Rugby Warwickshire CV23 9QZ United Kingdom Tel: +44 (0)1926 634400 Fax: +44 (0)1926 634401 email@example.com www.PracticalAction.org