Homogeneity[edit | edit source]
Eli Gooding (talk) 06:58, 3 December 2015 (PST)
- Close off print volume to remove printing from all reactive atmosphere Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Infill print volume with inert gas Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Place evaporating cleaning solvent onto each print layer Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Ensure consistent printing speed Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Consistent print temperatures Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Control cooling rates Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Supply consistent or precision materia lEli Gooding (talk) 07:38, 3 December 2015 (PST)
- Supply or design material that has been fabricated for non-ideal conditions Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Precision components for consistent printer production Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Standardize all components of printer Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Make all components with a "jig" or automation to ensure no variation between components Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Print in a vacuum Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Temperature controlled bed to keep material at wanted temperature Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Temperature controlled print volume Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Limit radiant heat from extruder to focus on the print spot Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Use the material's inherent resistivity and run current through part keeping entire part at a desired temperature Eli Gooding (talk) 07:38, 3 December 2015 (PST)
- Dwell between layers to keep part below desired temperature Eli Gooding (talk) 07:48, 3 December 2015 (PST)
- Use high thermal conductive inert gas to cool part quickly within a closed print volume Eli Gooding (talk) 07:48, 3 December 2015 (PST)
- Use a cooling gas at extruder tip to rapidly cool part Eli Gooding (talk) 07:48, 3 December 2015 (PST)
- Speed print speed to reduce excess heating of part Eli Gooding (talk) 07:48, 3 December 2015 (PST)
Yanibeeker (talk) 07:53, 1 December 2016 (PST)
- Print in vacuum Yanibeeker (talk) 07:53, 1 December 2016 (PST)
- Keep filament isolated from atmosphere (capsule)Yanibeeker (talk) 07:53, 1 December 2016 (PST)
- Clean bed with UV light before printsYanibeeker (talk) 07:53, 1 December 2016 (PST)
- Shine bacterial killing UV light on part to kill bacteriaYanibeeker (talk) 07:53, 1 December 2016 (PST)
- Use an edge on the hot end to swipe the part to eliminate layering effectYanibeeker (talk) 07:53, 1 December 2016 (PST)
- Magnetic field to create mold to eliminate layersYanibeeker (talk) 07:53, 1 December 2016 (PST)
- Heater to keep print somewhat soft to provide better layer to layer adhesionYanibeeker (talk) 07:53, 1 December 2016 (PST)
- Sensor to detect printing imperfections (missing layer) (pealing)Yanibeeker (talk) 07:53, 1 December 2016 (PST)
- Print layer with fan funneling warm air to deposition regionYanibeeker (talk) 07:53, 1 December 2016 (PST)
- Control the temp of printing atmosphereYanibeeker (talk) 07:53, 1 December 2016 (PST)
- Both heating and cooling fans to keep different areas on the object at difference temperaturesYanibeeker (talk) 07:53, 1 December 2016 (PST)
- Slow extrusion rate on vertices to eliminate bumpy effectYanibeeker (talk) 07:53, 1 December 2016 (PST)