Prepare emergency means beforehand to compensate for the relatively low reliability of an object. • Magnetic strip on photographic film that directs the developer to compensate for poor exposure • Back-up parachute • Alternate air system for aircraft instruments

This principle is proposed to solve the following contradictions: 1/271/342/345/137/279/2710/1110/3411/3313/514/2714/3214/3415/2718/2819/2722/2727/427/927/1227/1427/1827/1927/2127/2227/2827/2927/3427/3828/2728/3429/2730/3532/1332/3432/3734/134/234/734/1034/1434/1534/2734/3234/3635/3037/1337/3238/27 - See more at: http://www.triz40.com/aff_Principles_TRIZ.php#sthash.Ktouxg5P.dpuf

Beforehand cushioning

  1. Change the grease used on the guide rods to reduce the sound of the 3D printer.Ampringl (talk) 07:53, 1 December 2015 (PST)
  2. Change the material of the print bed to a more elastic one than glass to absorb more energyAmpringl (talk) 07:53, 1 December 2015 (PST)
  3. Alter design of 3D printer to remove screws and install snapfits to allow ease of replacement of parts.Ampringl (talk) 07:53, 1 December 2015 (PST)
  4. Add cushions to bottom of printer to reduce vibration(sound) and improve precision. Ampringl (talk) 07:53, 1 December 2015 (PST)
  5. Add a secondary fan system to further control the temperature control and as a back up if the primary fan fails. Ampringl (talk) 07:23, 3 December 2015 (PST)
  6. add small cushions to the side of the printer for side protection.Ampringl (talk) 07:23, 3 December 2015 (PST)
  7. Add muliple beds which can slide out from the center of the printer revealing another printer bed.Ampringl (talk) 07:23, 3 December 2015 (PST)
  8. Change the bed screw holds to a gliding hold to allow the single print bed to be removed easily.Ampringl (talk) 07:23, 3 December 2015 (PST)
  9. Conduct a preliminary adhesive print to act as the glue we currently use.Ampringl (talk) 07:23, 3 December 2015 (PST)
    1. an additional print head would be helpful and a method to switch between them.Ampringl (talk) 07:23, 3 December 2015 (PST)
  10. Add rotary printing head set up to print multiple materials.Ampringl (talk) 07:23, 3 December 2015 (PST)
  11. Include a cleaning kit to remove built up plastic in the feeder motor.Ampringl (talk) 07:23, 3 December 2015 (PST)
  12. Modify the guide rods to be segmented(slide into themselves) to adjust their distance from the center.Ampringl (talk) 07:23, 3 December 2015 (PST)
  13. Modify Carriage to have 4 magnet slots(2 mirrored about their current position) to allow ease to switch to the motors moving a bed rather than a print head. Ampringl (talk) 07:23, 3 December 2015 (PST)
  14. Switch from the wooden frame to a segmented printed hexagonal(with empty space) architecture with snap fits to allow ease of construction and packing.Ampringl (talk) 07:23, 3 December 2015 (PST)
    1. This would allow more airflow to the underside of the printer.(if the side boards were modified in this way)Ampringl (talk) 07:23, 3 December 2015 (PST)
  15. Add a secondary belting system to reduce the tightening of components overtime.Ampringl (talk) 07:23, 3 December 2015 (PST)
  16. Add in a cover for the bottom of the printer, to take weight off of the 3 columns as protect the printer's brain.Ampringl (talk) 07:23, 3 December 2015 (PST)
    1. This should still have holes in the design to promote airflow.Ampringl (talk) 07:33, 3 December 2015 (PST)
  17. Add in fans to the base wooden design in order to cool the printer bottom more effectively.Ampringl (talk) 07:33, 3 December 2015 (PST)
  18. Add a air system to replace the fan to control cooling to a greater degree.Ampringl (talk) 07:33, 3 December 2015 (PST)
  19. Add a liquid cooling system for prints which need cool temperatures. Ampringl (talk) 07:33, 3 December 2015 (PST)
  20. Modify connecting rods to be bent in a semicircle to allow printing on angles for more complex geometries. Ampringl (talk) 07:33, 3 December 2015 (PST)
  21. Add a backup filament tube to switch out filaments before the filament motor. (kind of like a switch mechanism but for filaments)Ampringl (talk) 07:37, 3 December 2015 (PST)
  22. add a sponge like material right before the filament goes into the motor to collect dust/contamination on the filament.Ampringl (talk) 07:37, 3 December 2015 (PST)
  23. add a liquid cleaner onto the filament before it enters the feeder motor which will evaporate off upon printing.Ampringl (talk) 07:37, 3 December 2015 (PST)
  24. Add a lazer sensor to the bottom of the end effector to detect the actual distance for calibration and protection of the bed purposes. Ampringl (talk) 07:37, 3 December 2015 (PST)
  25. Add epoxy/glue to the connector plate to ensure it stays securely in the frame.Ampringl (talk) 07:40, 3 December 2015 (PST)













  1. Add extra layer of glue to mirror so you don't scratch it Njlanter (talk) 07:50, 1 December 2016 (PST)
  2. print bumpers for wood Njlanter (talk) 07:50, 1 December 2016 (PST)
  3. Use laser rod detection to detect if rods fall off Njlanter (talk) 07:50, 1 December 2016 (PST)
  4. Put a little extra grease on bearings Njlanter (talk) 07:50, 1 December 2016 (PST)
  5. Check mechanical parts before printing Njlanter (talk) 07:50, 1 December 2016 (PST)
  6. Add backup cooling fan Njlanter (talk) 07:50, 1 December 2016 (PST)
  7. Put protective coating over mirror so it doesn't break
  8. Change wood frame to metal frame to avoid warping Njlanter (talk) 07:50, 1 December 2016 (PST)
  9. Replace printed parts with professionally made parts Njlanter (talk) 07:50, 1 December 2016 (PST)
  10. Clean your nozzle before printing Njlanter (talk) 07:50, 1 December 2016 (PST)
  11. Remove dog fur from grease (i have a dog) Njlanter (talk) 07:50, 1 December 2016 (PST)
  12. Add a filter for filament before entering extruder Njlanter (talk) 07:50, 1 December 2016 (PST)
  13. Buy a razor to remove difficult prints from bed Njlanter (talk) 07:50, 1 December 2016 (PST)
  14. Use a more powerful power supply to compensate for having to lower the fan to print at higher temperatures Njlanter (talk) 07:50, 1 December 2016 (PST)
  15. Buy extra filament so you don't run out Njlanter (talk) 07:50, 1 December 2016 (PST)
  16. Put printer next to a smoke detector if leaving it alone Njlanter (talk) 07:50, 1 December 2016 (PST)
  17. Print out replacement parts because the ones on the printer will fail Njlanter (talk) 07:50, 1 December 2016 (PST)
FA info icon.svg Angle down icon.svg Page data
Authors Adam Pringle, Nicholas Lanter
License CC-BY-SA-3.0
Language English (en)
Related 0 subpages, 2 pages link here
Impact 21 page views (more)
Created December 1, 2015 by Adam Pringle
Last modified February 6, 2023 by Felipe Schenone
Cookies help us deliver our services. By using our services, you agree to our use of cookies.