Line 52: Line 52:
# [[File:AthenaII_attach_verticals.JPG|thumb|right|Attach vertical boards.]] Insert M3 x 50 mm socket head cap screws with M3 washers through the holes in a vertical board. Push the screws through their holes in the idler and motor ends. The holes will not align with the screws if the apex isn't properly assembled, e.g. the ends aren't fully pushed onto the guide rods. Secure the board in place with M3 nuts and M3 flat washers on the idler end and only nuts on the motor end (there is insufficient clearance for washer). Repeat with the remaining two apexes.{{clear}}
# [[File:AthenaII_attach_verticals.JPG|thumb|right|Attach vertical boards.]] Insert M3 x 50 mm socket head cap screws with M3 washers through the holes in a vertical board. Push the screws through their holes in the idler and motor ends. The holes will not align with the screws if the apex isn't properly assembled, e.g. the ends aren't fully pushed onto the guide rods. Secure the board in place with M3 nuts and M3 flat washers on the idler end and only nuts on the motor end (there is insufficient clearance for washer). Repeat with the remaining two apexes.{{clear}}
# [[File:athenaII_attach_extruder_drive.JPG|thumb|right|Attach the assembled extruder drive.]] On the apex having all the limit switch wires, position the extruder drive about half way up the vertical board and with the fuel hose angled up and to the right (see picture). Secure in place with two #6 x 1/2" sheet metal screws.{{clear}}
# [[File:athenaII_attach_extruder_drive.JPG|thumb|right|Attach the assembled extruder drive.]] On the apex having all the limit switch wires, position the extruder drive about half way up the vertical board and with the fuel hose angled up and to the right (see picture). Secure in place with two #6 x 1/2" sheet metal screws.{{clear}}
# [[File:athenaII_end_effector_attached.JPG|thumb|right|Attach the end effector.]] Place a small amount of grease on the ends of the connecting rods and engage them with the magnets in the carriages. Engage the opposite end of the connecting rods with the magnets in the end effector. Note the orientation of the end effector - the connecting rods on one carriage must be parallel, otherwise the end effector is uncontrollable.{{clear}}
# [[File:Athena_grease_ball_bearings.JPG|thumb|right|Place a small dab of grease on connecting rod ends.]] Place a small amount of grease on the ends of the connecting rods and engage them with the magnets in the carriages.{{clear}}
# [[File:athenaII_end_effector_attached.JPG|thumb|right|Attach the end effector.]] Engage the opposite end of the connecting rods with the magnets in the end effector. Note the orientation of the end effector - the connecting rods on one carriage must be parallel, otherwise the end effector is uncontrollable.{{clear}}
# [[File:athenaII_bowden_sheath.JPG|thumb|right|Attach the Bowden sheath.]] Push the 4mm PTFE tubing into the pneumatic quick-connect on the extruder drive. Tie the fan, thermistor and hot end wires to the Bowden sheath with three or four small wire ties. Do not over-tighten the wire ties as they can constrict the Bowden sheath and block the movement of filament.{{clear}}
# [[File:athenaII_bowden_sheath.JPG|thumb|right|Attach the Bowden sheath.]] Push the 4mm PTFE tubing into the pneumatic quick-connect on the extruder drive. Tie the fan, thermistor and hot end wires to the Bowden sheath with three or four small wire ties. Do not over-tighten the wire ties as they can constrict the Bowden sheath and block the movement of filament.{{clear}}
# [[File:athenaII_attach_spool_holder.JPG|thumb|right|Attach the spool holder.]] Run all of the wires down the right side of the vertical board, pulling them towards teh bottom of the frame. Secure the wires in place with the spool holder, placed about halfway between the extruder drive and the bottom of the printer. Secure the spool holder with two #6 x 1/2" sheet metal screws.{{clear}}
# [[File:athenaII_attach_spool_holder.JPG|thumb|right|Attach the spool holder.]] Run all of the wires down the right side of the vertical board, pulling them towards teh bottom of the frame. Secure the wires in place with the spool holder, placed about halfway between the extruder drive and the bottom of the printer. Secure the spool holder with two #6 x 1/2" sheet metal screws.{{clear}}

Revision as of 14:22, 13 June 2018


Materials and Tools

File:AthenaII final mechanical materials.JPG
Final mechanical assembly materials.
Materials
Description Count
Print effector with magnets affixed 1
Print quick connect thumbscrew 1
Assembled Hexagon hot end 1
Assembled 40mm fan 1
M3 x 12mm socket head cap screw 2
Reamed pneumatic quick connect fitting 1
2mm id x 4mm od PTFE tubing about 63cm
Small wire tie 1
File:AthenaII final mechanical tools.JPG
Tools.
Tools
2.5mm hex key
Precision knife

Notes

Procedure

  1. Snap carriages onto LM8UU bearings.
    Snap the carriages onto the LM8UU bearings with the magnets facing down. Repeat with remaining two apexes.
  2. Attach vertical boards.
    Insert M3 x 50 mm socket head cap screws with M3 washers through the holes in a vertical board. Push the screws through their holes in the idler and motor ends. The holes will not align with the screws if the apex isn't properly assembled, e.g. the ends aren't fully pushed onto the guide rods. Secure the board in place with M3 nuts and M3 flat washers on the idler end and only nuts on the motor end (there is insufficient clearance for washer). Repeat with the remaining two apexes.
  3. Attach the assembled extruder drive.
    On the apex having all the limit switch wires, position the extruder drive about half way up the vertical board and with the fuel hose angled up and to the right (see picture). Secure in place with two #6 x 1/2" sheet metal screws.
  4. Place a small dab of grease on connecting rod ends.
    Place a small amount of grease on the ends of the connecting rods and engage them with the magnets in the carriages.
  5. Attach the end effector.
    Engage the opposite end of the connecting rods with the magnets in the end effector. Note the orientation of the end effector - the connecting rods on one carriage must be parallel, otherwise the end effector is uncontrollable.
  6. Attach the Bowden sheath.
    Push the 4mm PTFE tubing into the pneumatic quick-connect on the extruder drive. Tie the fan, thermistor and hot end wires to the Bowden sheath with three or four small wire ties. Do not over-tighten the wire ties as they can constrict the Bowden sheath and block the movement of filament.
  7. Attach the spool holder.
    Run all of the wires down the right side of the vertical board, pulling them towards teh bottom of the frame. Secure the wires in place with the spool holder, placed about halfway between the extruder drive and the bottom of the printer. Secure the spool holder with two #6 x 1/2" sheet metal screws.
Assembled AthenaII sans electronics.
Assembled AthenaII sans electronics.

Navigation

Preparatory Materials
Printer Primer
Overview
AthenaII Printed Parts Glossary
Non-Workshop Tasks
Assembling hot end
Soldering and tinning
Workshop Tasks
Track 1 Track 2 Track 3
Connecting Rods Frame Epoxying Magnets
Epoxying Magnets Connecting Rods End Effector
Extruder Drive and Spool Holder Epoxying Magnets Frame
End Effector Extruder Drive and Spool Holder Connecting Rods
Frame End Effector Extruder Drive and Spool Holder
Final Mechanical Assembly
Before 2019 Starting 2019
Wiring/Melzi + BB Wiring/Athena Board
Firmware and Calibration Firmware and Calibration - (Wireless Setup) - (Update Franklin)
Software and First Print
Follow-up information
Printing Basics
Maintenance
Cookies help us deliver our services. By using our services, you agree to our use of cookies.